Jump to content
SAU Community

Noob Seeking Advice

ThePimp

By ThePimp,
in Western Australia

 Share

Recommended Posts

ThePimp Rookie

ThePimp

Posted
Posted

Dear Seniors

I just got my R33 GTST and am intending to convert it from AT to MT by December.

I am also going to tune up the car to a Drift Ready state maintaining street drivability.

I have the intention to do the following in due course after my MT and Exhaust initial mod and am looking at advice on Viability and availability:

1. Handling - the standard stuff like Coil over, Tower Bars and ARB. Looking for recommendations. Plus Advice if member braces are required?

2. Handling - Looking for advice if it is advicable to remove HICAS. I am looking to change my steering to one with quick release BOSS but can give that up if HICAS is more recommended.

3. Turbo - I am thinking of a Garette GT0376 or similar (Prefer Ball Bearing so the IHI comparable might be a good alternative) Looking at 1.2bar Boost Max... Any Engine mods required or recommended? Stut bolts? Pistons and Con Rods? Actually I might lower the boost if i need to take the engine apart.

4. Intercooler - the natural thing with Turbo would be a totally trick FMIC... Please recommend...

5. Auxillary parts - Fuel Injectors, Surge Tanks, External Pumps...

6. Most important part - The Brains!!! What ECU is popular here? Where can I get competent and affordable tuners? Where is a good hub dyno that wun cost me an arm or a leg? I am familiar with most modern ECUs like MoTec, Power FC, and F Con V Pro... I am unable to touch Motec and F Con due to the large amount of wiring works, Power FC due to computer connector... So I'll probably need someone to install and tune...

Glad to receive any advice...

Cheers

Link to comment
https://www.sau.com.au/forums/topic/408704-noob-seeking-advice/
Share on other sites
mz.qiksky Explorer

mz.qiksky

Posted
Posted

If you just got the car I recommend you do the manual conv and then work on the handling side of things.

IMO no point in boosting the power until you know how to drift it, otherwise you just play tag with the walls. I have a friend who has just started drifting... his starter car is an R32 with an RB20E which is perfect. Simple mods will be fine, FMIC, pod filter, new brake pads/fluid are good too and some decent suspension.

If the 33 runs electronic HICAS you can remove the steering rack and replace it with a lock bar. Some places sell collars that will lock the steering rack but you're better off replacing the whole thing with a lock bar.

OptiC Enthusiast

OptiC

Posted
Posted

Mate, if your free tomorrow night head up to the track for the drift prac that's on.

If you ask for the drift trainer named Marc the officials can point you in my direction and you can get an idea of the basics from there.

As mentioned above leave the power mods for now, make the car drive right and sto right then move onto that stuff. I would also add a fixed back seat to the list for one of your first mods, it makes a bigger difference than you would think!

Also www.driftwa.com.au

ThePimp Rookie

ThePimp

Posted
  • Author
Posted

I was at the back section of the track all night and yeah pretty busy up there. We had about 15 cars just in the training area!

Usually one a month at this point mate, check the WASCC web page for the calendar or like WADrift on FB ;)

Tha mate!

I happen to also notice Barbagallo Drift Assault on 30 September and 1 October... I'll be hopping by in the arvo on 30 September but I'll have to miss 1 October as I have a class test going on that day...

Cya there if u r there mate...

  • 3 weeks later...
Steve Grand Master

Steve

Posted
Posted

You want to drift - sell it, buy a 32

You are talking about spending a lot of money, those parts aren't cheap, then add in labour

If it needs to be a 33, see how much a manual costs, compare the cost to what you will be paying (gearbox, shifter, decent clutch, pedal boxes and pedals, master and slave cylinder - prob going to cost you 3k or more in parts

But a 32 is much much better for sliding than a 33, more fun and cheaper

Just my opinion anyways (havin owned both and drifted both)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      S1 rb25/s14 starting problem

      By Dose Pipe Sutututu · Posted

      When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...