Jump to content
SAU Community

R32 Gtr Idling Issues

SiR_RB

By SiR_RB,
in Engines & Forced Induction

 Share

Recommended Posts

SiR_RB Grand Master

SiR_RB

Posted
Posted (edited)

Hey guys, lately my car started to "hunt" at hot idle, I suspected the stock paper intake gaskets were the problem so I changed them all to HKS metal items,

Still did it abit so I wound the screw out of the AAC valve and all seemed much better, then today when I did a cold start it only reved to 1100ish when first cold, then goes to 1000at hot idle? Used to idle higher then slowly drop to 1000rpm

Then I went to start the car after it sat for about 30mins or so and revs were very low hovering around 700rpm and needed to tap the throttle to bring it up, then it drops again, seems like its like this until it all gets to operating temp....weird

So far took aac valve out and cleaned it

Replaced intake gaskets with HKS metal items

Don't have any problems with it idling high at all, never have

Any suggestions?

Thanks

Edited by SiR_RB
Link to comment
https://www.sau.com.au/forums/topic/411277-r32-gtr-idling-issues/
Share on other sites
SiR_RB Grand Master

SiR_RB

Posted
  • Author
Posted

I've had the exact same issue, found one of the hoses from the air chamber up to the balance tube was split. As above smoke test will confirm where yours is

Hope it's not that cos I ain't pulling my plenum off again !! Il try manage to squeeze/dislocate my hand to reach under there lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      Absolutely could be. I collected data logs from when the O2 sensor was still out and also after I had replaced it so will try to compare them. Pretty confident that the affect is lowered with the new sensor, will check logs at the same RPMs/conditions. 
    • Bennym35
      New guy

      By Bennym35 · Posted

      Hey guys Long time lurker, I daily a nm35 stagea 250t rs four and I've had it for almost 2 years (very reliable 👌). Issues or just looking for information ill always find myself here having a read, so thought id join.  3inch stainless intake, pod filter, AM performance turbo dump pipe, 3inch hotdog, 3 and half inch stainless to 3 and half inch AM performance blast pipes. Bc racing coilovers. 18inch rims Hdi intercooler and trans cooler soon.  Here's my car
    • Songo
      New kid on the block

      By Songo · Posted

      thanks for the advice on the box... i was thinking the 6 speed was better for cruising on the highway but on closer inspection and comparison the Rb 5 speed box was not too different...  So the choice is going to be the RB25 box... if I can save up and find one at the right price  
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Matt, yes that's what i am aiming for. Just going to apply the right voltage and grounds to the dash connector. Hence my search for these pins... any chance you know if these pins are in the same spot as the ones on the S15 Dash connector? as mentioned above on page 8?
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Yes, unfortunately that's the one. Signal was noisy to begin with; after driving once and looking back at the logs I saw pressure constantly swinging between 0-200psi, or staying at 0 randomly for a few seconds. There's a lot of good sensors that share the same look and feel, so don't presume they're all bad. I bought mine for 20$ off Amazon and I should have read the reviews prior, as it's clear they're junk.  I purchased a lowdollerr motorsports sensor. 
×
×
  • Create New...