Jump to content
SAU Community

Recommended Posts

I use two waxes

1) for the body in general, a high quality Canauba wax eg Meguiar's Hi-Tech Yellow Wax #26

2) for taking off soot & discolouration from the rear bumper whilst running rich, Malco Nanotech Banana Wax. This product negates the need to use polish. This wax also permits the sealant to remain on top of an existing polished surface.

The overall process is still...

Wash > Clay Bar (if required) > Polish (of correct grade and best type) > Sealant > Wax

Link to comment
https://www.sau.com.au/forums/topic/411635-best-wax-to-use/#findComment-6580886
Share on other sites

It's true that without knowing how the car was treated by a former owner, we don't know how thick the existing paint is on each panel. This can be resolved by asking your local panelbeater or SAUer or Detailer for a 15 minute loan of a paint thickness gauge > thickness in microns = ???

Anything below 120 is thin and extra care needs to be taken if compounding/polishing.

But getting back to waxes, wax doesn't thin the paint. It coats the paint or sealant to give you a shine.

Link to comment
https://www.sau.com.au/forums/topic/411635-best-wax-to-use/#findComment-6580908
Share on other sites

  • 5 weeks later...

I stay away from any product that claims to be both a polish and a wax.

In between the polish and the wax should be the sealant which does several things which shouldn't be understated.

True true, best method is to always start at base one as terry mentioned and ensure you start with a solid clean, the clay bar, moving to a polish/wax remover and then progressing from there into a more detailed polish again and finally sealing with an appropriate wax.

Again, this is all subject to time and budget...and the condition of your car

Link to comment
https://www.sau.com.au/forums/topic/411635-best-wax-to-use/#findComment-6626514
Share on other sites

Hi guys,

For anyone out there that is not running a cat.... hmmmm. During a SAU detailing day, we tested 7-10 different products and found that one in particular worked extreamly well. P21S Total Auto Wash. Spray on to the area, let it site for 30Sec and wipe with a Microfibre cloth, gone.

For a wax there is a Japanese wax we have by Ion Coat called NAVI WAX. It is our best selling wax. There is a light and dark version. Very easy to use.

  • Wet the supplied applicator sponge.
  • Apply to a panel at a time
  • Immediately wipe of the panel with a high quality microfibre.
  • Continue around the car.

If you notice any hazing or smearing, go over the car again with a wet microfibre cloth then buff dry lightly with a dry MF cloth. Amazing depth and gloss.

Link to comment
https://www.sau.com.au/forums/topic/411635-best-wax-to-use/#findComment-6631401
Share on other sites

For a mid range wax i have used both the P21s wax and also the Pinnacle Sovereign wax. Both around the $60-$70 dollar mark but last for ages.

With these it is very important to make sure your paint is clean and well prepared. The results are just much better.

Link to comment
https://www.sau.com.au/forums/topic/411635-best-wax-to-use/#findComment-6638645
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...