Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...
  • 2 weeks later...

Hi i tried contacting you guys at OTR Motorsports in regards to a price but no response

could you please price me :

Bronze TE37 18x10 +15 & price on super laps Gunmetal - Red stickers - to 5045 S.A Thanks

18x11 cc03 fit on a 32 GTR with aftermarket big brakes without any dramas?

How much for set in polished bronze?

It shouldn't be a problem clearing your big brake kit, 18x11 will cost $1500. Currently all Bronze are sold out until another 2-3months

Hi i tried contacting you guys at OTR Motorsports in regards to a price but no response

could you please price me :

Bronze TE37 18x10 +15 & price on super laps Gunmetal - Red stickers - to 5045 S.A Thanks

Sorry mate, did you call our store? I apologize if you didn't get a response, just tell me who you spoke to?

PM you on pricing, we have TE37RT and TE37SL in stock but not the regular bronze..

  • 2 weeks later...

Sorry not making 17's anytime soon, most of the demand is 18's and 19's

Not sure what those pods are, it was on customers car already.

DSC_0822_zps26ec16bc.jpg

DSC_0813_zpsc40415e8.jpg

DSC_0824_zps30f466cc.jpg

DSC_0820_zps2a72881a.jpg

Hi Ken,

What are the specs for these wheels?

How much are for Matt Black, 19" 114.5 Stud 22+ offset cco3's??

Cheers

Above are 18x10 all round

Only have 19x8.5+22 and 19x9.5+22 in black $1600

Thanks Ken, Do you know whether a v35 non-brembo would require guards rolled or camber arms with 18x10 + 20 all around?

  • 3 months later...
  • 3 weeks later...



  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...