Jump to content
SAU Community

Recommended Posts

hey all,

i've decided to sell some parts from my shed, these were meant for my s13, but am selling due to wanting a motor bike to get my licence on.

the engine RB25DET is from a 1996 series 2 r33, i bought a complete stat written off car from the auctions (rear end damage).

so i have had the engine running and driving, it was a very clean car before the accident, i had a mechanic mate check it all out for me and theres no problems with it. it has 120xxxklms on it, (i have paper work from auction that can prove k's) to sum it up, it runs smooth, revs nice, comes on boost without a problem, the only thing i was going to do to it before putting it in my silvia was timing belt and water pump.

it comes as pulled from car, includes turbo, manifolds, wiring loom (un cut), afm ecu. etc etc.

im asking $1600 ono,

the gearbox (S2 rb25det 5speed manual box) is from the same car, when i drove the car up the street there were no problems with it,

shifted smoothly into every gear.

asking $1500ono

i also have a pair of front guards from the S2 r33, white in colour, no damage but they may have slight scuff marks from being in storage,

asking $200 pair

pair of r32 front guards, drivers side is in good condition, passenger side had a large dent in it which has been hit back out, will need repair and paint but is still useable.

asking $100 pair.

i will list other parts up as i come across them, (mostly interior and engine bay parts, nothing exciting)

all this stuff has to go, will take any reasonable offer,

parts are located in woodville nsw 2321, (40 mins from newcastle, 20mins from the end of the freeway)

i work in lambton so i can meet people around that area to drop any parts off.

if you need pics text me 0449669476 and i'll reply with pics.

Thanks,

Brock

pm sent mate,

also for sale are

r33 series 2 door trims and rear quater trims,

excellent condition, $150ono. the lot.

r32 dash, bubble in the usual spot and missing centre and passenger side air vent, $50

r32 standard platsic rear bar, black in colour, will probably need painting as its been in the shed for years, $20

i'll upload some pics tomorrow night mate,

more for sale,

2x pairs of r32 side/door mirrors, black, might need paint, $100 ono per pair

r33 manual tail shaft $150

r32 bootlid in black has been repainted, needs polish, has holes for wing, $80

r32 pair of tail lights, black, good cond, $50 pair

r32 centre console good cond, $20

r32 doors, black but been half sander down, include glass, motor etc, $200 ono pair

r32 rb20det front cross member, $120 ono

r32 rear cradle complete minus diff and rotors/ calipers, $100

r32 rb20det radiator-manual, $50

also have the boot, door and window seals/rubbers for sale, let me know what you need and i'll give you a price

Engine sold

still got everything else there,

Also got a '92 r32 shell for sale, is rolling, no panels, no brakes/diff etc,

will come with all the interior i still have left from it.

few things left in engine bay, has rust around rear window, message me if you want to see some pics

not sure what its worth, say $1000 negotiable, send me some offers, perfect for track car, or it can be re-registered.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The fab work can be as simple as a couple of silicon hoses and clamps to the factory piping. 
    • Just sounds like either way you need to do some fab work to get everything to fit, so why limit yourself at that point? If the GCG high flow option is zero effort in and out swap though I'd probably do that. It's almost certainly lowest risk, lowest cost, etc. The HKS GTIII-RS option that Kapr mentioned is laughably expensive for what it is, they charge the exact same for two turbos on the RB26 so their margins are off the charts on that thing.
    • Intake manifold is not a part of the issue. The turbo bolts to the exhaust manifold. That is easy. But close your eyes and picture the physical situation. That is a T3 flange on the manifold and a T3 flange on the turbo. As long as any new turbo has a T3 flange on the exhaust housing, that exhaust housing will bolt to the exhaust manifold. This places the exhaust housing in the same place as the stock one. But now move your mental attention a little further forward. The location of the compressor housing is set by the length of the turbo's core. The stock turbo had a long core. Let's say that it is..... 100mm long. So that would place the compressor housing 100mm forward of the exhaust housing. But a highflow, might well have a centre core that is shorter. Let's say that it is only 70mm long. Now the compressor housing will be 30mm further back in the engine bay than the stock one. This DOES move the turbo's compressor outlet backwards. It also moves the compressor's inlet backwards. You will very likely have to do some work to both the inlet and outlet piping to make everything connect again. I am not say this to make it out to be a bigger deal than it is. I am just pointing out that "bolt on" is sometimes not quite bolt on. The highflow from GCG that Murray linked above (https://gcg.com.au/turbo-charger-upgrade-skyline-gtst-2iu-xtrgts-s1.html ) uses a core that is the same length as the stock core, and so does not require this extra work. It will look very much like the stock turbo. No-one uses GTR turbos of any flavour (stock, or aftermarket) in a single turbo application on RB20/25. It's not a thing. Yes, people have been putting on GT3076, GTX3076 (and bigger and smaller versions of those) and G30s (of various sizes) onto RB20/25 since forever. But these are not "bolt on". Everything except the 4 bolts to the exhaust manifold change with these. And genuine Garretts are expensive. Non-gen, like Pulsar, etc, are cheaper, variously as good or nearly as good. But still not bolt on. No-one in the right mind would pay for an HKS turbo. Not in this modern day and age. Well, yes, the GCG highflow. You could ask HG what he can do to make the compressor housing sit in the original location. There are surely others doing highflows around the world. And some of the eBay/Temu ones (as reported by Dose) work and don't die. Bit of a lottery though. I would send your turbo to GCG (here in Oz) to be highflowed if you want a trivial no-extra-work option. But seriously, the work required to change inlet and outlet piping is not that hard. That's a boost control problem, not a turbo problem.
    • Thank you all for the replys 🙂 I know that intake would be different but that is one pipe at it is not that hard to get(custom one). I meant mainly bolt to the stock manifold and the turbo elbow. I looked and many sites/forums but they are just "old" with some old HKS turbos from GT-R i guess? What about some Garrets?  Or any other turbo? Is there even a turbo which i can just bolt on? 😄 And yeah i know about that new HKS but that is like 2000k USD without taxes/shipping in here   Iam getting a touch up tune but my "problem" is that on the "not" hot day iam getting peaks around 0,9 bar...and when it was around 15 Celsious i saw peak around 1 bar which is just too much for stock turbo. And of course turbo is old and i like to get some new one for a piece of mind 🙂 
    • I'm working on the assumption that our friend Jasmine here is a Russian (or, possibly Ukrainian) spammer/spambot, based purely on the number of such that I have been having to neuter in the last few weeks. IP address for the OP above was in WA. But that could have been via VPN. Posting at quarter to 4 in the morning is a good sign of being from somewhere in Europe. The last Jasmine that I kicked in the cooch was IP addressed in Ukraine. Even that could have been via VPN, and the bitchbot could have been from Russia, Serbia, China or anywhere. Regardless, was a spambot, so I killed it with fire. The fact that our new friend Jasmine here did not respond in any way to my tart query strongly suggests to me that this OP was just the establishment phase of a user able to be activated for spamming in a week, or 3 or 10.
×
×
  • Create New...