Jump to content
SAU Community

Recommended Posts

Just had my V up-rev tuned, 227.3 rwhp (169 rwkw) before tune 245.1 rwhp (183 rwkw) after. Pulls alot harder especially mid range, revs to 7000rpm and still has more go but a bit cautious to go any further. The up-rev tune was done by PZP in Perth. $550 :thumbsup:

  • Replies 96
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

So worth it hey. Couldnt believe the improvement in torque and response.

i notice it most in mid range, from 80k's up it seems to just get stronger. 2nd gear 110km/h @7000rpm and still had some stick....but was cautious to go any harder. Fully recommend for any one interested in squeezing all they can from a N/A engine :yes:

Hey Gerard, what mods have you got?

Hey xj265 Z tube, K&N high flow filter in stock air box, MD 5/16 plennum spacer, throttle body spacer, Y pipe stock cat back, transgo shift kit, Lovells springs, Kinetix full camber/traction kit and now Up-rev tune :D

Thats complicated! First run was 166rwkw without a tune.

My ECU didn't seem to like Uprev; it had a Master rom version they hadn't seen before so its with Uprev to get it sorted.

Hopefully will be sorted before the new year :)

  • 3 weeks later...

540786_457003624346812_521769213_n.jpg

I'm stoked! This is with the cheap and nasty compliance air filter and cats (that are mismatched).

Mods to come: replace awful y-pipe/cats, new air filter.

Current mods: Motodyne 5/16 spacer, Rev up air box, stillen z-tube, JIC Magic Spartan DE Catback, chinese y-pipe

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
×
×
  • Create New...