Jump to content
SAU Community

Recommended Posts

3'' cat back exhaust for r32gtst, mandrel bent, mild steel, as new, 3'' stainless muffler, includes 3'' high flow cat $500

rb25 plenum lower half runners sold

rb25 injectors, fuel rail, reg and wiring $150

rb25 crossover pipe with BOV $50

std cam gear rb $20

rb25 throttle body no tps,sold

rb20 throttle body no tps $40

std rb25 exh manifold $50

r32 power steer pump good condition, hicas type $50

r32 hicas rear steering rack $50

R32 airconditioner condenser/pump and all hoses etc $100

rb20 rocker cover gasketbrand new from nissan $40

r32 gtst front seats very good condition $100 the pair

r32gtst rear seat compete, very good condition $100

also have a set of brand new r34 gtt shocks with springs $150neg

r34 gtr front shocks and springs $150neg

I have set of height and damper adjustable coilovers to suit r33/34gtr, in very good condition and not as harsh as many but still give very good handling $900, will post pics soon

these can also fit r34 gtt, the rears are perfect and the fronts with my supplied spacer plate will fit fine but are very low and scrape slightly on hard lock, but if you like it low and are carefull they will be ok

will ship at buyers expence but for some items adeliade buyers prefered, email [email protected] for pics or to negotiated on price

Link to comment
https://www.sau.com.au/forums/topic/41606-3exhnismo-coilovers-3334rr32-seats/
Share on other sites

Can the height and damper adjustable coilovers fit an R32 GTR? Also, how is it exactly, I don't think they would be as low as mine right now but need to know because I'm looking at raising my car a bit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...