Jump to content
SAU Community

Recommended Posts

Clearing out left overs in the garage. I'm located in Sydney, would prefer to sell locally but will consider posting.

Contact me via text on 0468 330 099 and let me know what you're after. Am negotiable but within reason.

Turbosmart dual stage boost controller. Whats shown in the photos is included. Chasing $150 ono.

yK0hG.jpg

Drift branded gauges. Water temp and Oil pressure. Comes with oil pressure sender to suit RB. Also electrical wiring for one gauge included. Chasing $60 ono.

cG7qb.jpg

R32 front auto spoiler with the motors. Quite rare, was working perfectly fine, got in the way of my front mount so had to remove. Some scarring on the front and underside. Chasing $250 ono.

noPnw.jpg

R32 gtst front bar. Factory dark blue colour, has a few battle scars and a crack in the front. Cable tie it up if you really need. Chasing $60 ono.

dvtVW.jpg

sDox3.jpg

R32 factory side mount intercooler with piping. Chasing $50 ono.

BXyn0.jpg

R33 GTR Starter motor (from memory) but is interchangable, was going to use on my r32 gtst but didn't need it afterall. Chasing $50 ono.

sBZ5u.jpg

R32 GTST 2 door vertex style side skirts. Brand new, tried to trial fit but they were to tight so never installed them, may need altering to fit. Chasing $120 ono.

vlBey.jpg

R32 GTST 2 door mud flaps full set front and rear. Factory dark blue colour, good condition. Chasing $50 ono.

HGkNT.jpg

R32 ashtray. Front flap/door missing but still better than nothing if you need one but don't mind seeing inside the ashtray. Chasing $15 ono.

8UbwX.jpg

Boost gauge. T-Sport brand reads in psi. Have no idea if this works have never fitted it, came with the car. The plastic garnish around the inside is loose. Chasing $15 ono.

ykCEE.jpg

f0qCG.jpg

Brand new Nissan skyline 1987-1994 aerpro wiring harness for aftermarket headunit. Chasing $15 ono

xKZig.jpg

Edited by dee-20t
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...