Jump to content
SAU Community

Recommended Posts

A lot of people here say these are the equivalent of the HKS 2530 turbos and driving a few cars around the track that mates own in various different tunes would be about right.

All dyno plots are very similar, spool up, lap times, 1/4 mile ET and MPH times are surprisingly similar.

These were running 17 psi before the rebuild and hit hard by 3,800 RPM, 1st gear would light up the tyres as soon as it hits boost! People freak when they see a GTR light up the wheel under acceleration (not dumping the clutch)

Good for about 500 wheel hp these are an excellent balance between street and outright power. I made about 410 on 17 psi which is a good balance as it does not over power the suspension, brakes and excessively strain the engine.

My mods are:

computer

Exhaust

Intercooler pipe kit

Pod filters

Cam gears

These turbo's have NOT been used since the rebuild!

I am located in Sydney but can ship interstate.

$2700 ono or highest offer

Could you please provide either a photo or list numbers from the id tag in the centre of the turbo shaft. This will confirm the turbos as N1.

Sorry to be a doubting Thomas, but there is an awful lot of confusion about which turbo is which & the only way to be sure is to cross check the part numbers.

Cheers

Hope you don't mind, but here's a page of details for the various Nissan turbos for the GT-R's:

http://www.systranbox.com/systran/box?syst...an_f=1086005489

The ones being sold are mentioned as being R33 GT-R N-1 turbo's. I have a set of the BNR32 NISMO turbos and although not fully tuned yet, know they have great potential.

Cheers

Brendan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...