Jump to content
SAU Community

Recommended Posts

Very Original Nissan Skyline Series 3

Last Series - Made in Australia

Factory 5 Speed Manual

Genuine Low 188,000 K's

Only ONE previous family OWNER [ deceased estate ] before me. I have owned this Skyline for over 10 years.

All Original Panels

Original Vic Rego as upon Dealer Purchase

Factory Air Conditioning [ full working order ]

Factory Power Steering

Factory/Dealer fitted Hayman Reece Towbar

New EXTRA Heavy Duty Nissan Patrol RB30 CLUTCH and new Front Shockers installed about 18 Months ago

New WATER PUMP - TIMING BELT done at the same time installed about 6 Months ago

New BALL JOINTS, NOLATHANE Bushes, Front and Rear BRAKE Pads, new TYRES installed about 3 Months ago

Serviced every 5000 kms with Oil AND Oil Filter

VERY WELL MAINTAINED - HAS NEVER LET ME DOWN

Genuine Sale - initially I was going to retain this VERY RELIABLE Skyline hence the reason I spent all the $$ and time listed above BUT unfortunately I now require a bigger vehicle.

Sold with Rego AND RWC for full asking price of $4,995.

**Please NO time wasters - GENUINE inquires only**

Call me, MARK on [ 03 ] 9884 0246 to organise inspection, car location - Vermont

Skyline also advertised elsewhere including CarSales, etc

As I work on Shift - Please leave contact details if phone unanswered.

post-71149-0-71744700-1360171870_thumb.jpg

post-71149-0-09679500-1360171883_thumb.jpg

post-71149-0-45710300-1360171897_thumb.jpg

post-71149-0-18537000-1360171904_thumb.jpg

post-71149-0-89172600-1360171912_thumb.jpg

post-71149-0-00983700-1360171927_thumb.jpg

post-71149-0-73187800-1360171932_thumb.jpg

Edited by MMMSSS

Hey buddy, put this on car sales if your after that sort of money. It is very well maintained however it's still only an aus spec r31 not a GTS/X.

Good luck with the sale

  • 2 weeks later...

New EXTRA Heavy Duty Nissan Patrol RB30 CLUTCH and new Front Shockers installed about 18 Months ago

MORE INFO !!

** When Gearbox out - New Genuine Nissan Rear Gearbox Seal then Special Treatment with Ultra High Performance REDLINE Racing Shockproof Gearbox Fluid - " Blue Smurf " for people in the know

Since then - Shift Changes - Magic ! - Like a Hot Knife through Butter ! **

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...