Jump to content
SAU Community

Recommended Posts

update?

Also, what type of oil and how much did they use?

Can greatly affect the life of the compressor.

Hi Luke,

After inspection, it looks as though the AC compressor had overheated internally and seized.

The A/C specialist suspected the pressure's were too high due to the older original condensor design as the system was not designed to operate on R134a.

We used PAG46 oil in the new A/C compressor. Between 160-180ml.

Did they replace the reciever drier and clean out all the lines? Cause the metal shavings from the first failure will kill a new compressor very fast

Yes they replaced the reciever drier, cleaned out all the lines, even replaced one. Also did the evaporator, TX valve under the dash. Cleaned the lined out with Shellite. The works.

Hi All,

OK so here is the update and where I am up to.

I have 3x GTR R32 A/C compressors. 2x Zexel (original one off the car that leaked and a second hand working one I bought recently) & 1x Valeo (the new one that failed)

The specialist pulled apart all 3 of them and made 1 really good one. Looks like he decided to use the Zexel housing.

180ml of n8 denso oil has been put in it and we fitted it to the car.

Next we have removed the old condenser from the car, drilled out the rivets and removed the mounting brackets to be reworked into a new universal condenser.

The reason for using a new universal condenser is because it was suggested that the pressures with the original condenser was to high after retro fitting with134a gas.

The old condenser was a 'Serpentine' type and the new I bought is a much more efficient 'parallel flow' condenser.

Just waiting for the rain to clear so that we can fit it to the car, then have to clean all the lines again before recharging the system and it should be ready for winter lol.

Pictures to follow..

Edited by paulyp
  • Like 1

Hmmm.

I have a feeling it may be over oiling.

I have run 134a without any issues.

Even in temps as high as 40°.

Do you know how many mls you put in yours?

Paulyp, did you modify your condenser fan to turn on with the air con?

Hi Dark26, Yes that was modified to turn on whenever the air-con was running.

Will check the fan before re-fitting to make sure its still ok.

Do you know how many mls you put in yours?

Hi Dark26, Yes that was modified to turn on whenever the air-con was running.

Will check the fan before re-fitting to make sure its still ok.

cant remember.

Would have been around the 30ml mark.

But, I will check the workshop manual and let you know what Nissan recommend.

  • 4 months later...

Hi all,

Just another update for everyone.

We have finished fitting the AC about 2 months ago and its working well.

Went through alot of effort to fabricate brackets and have hoses made to fit. Also had to modify the standard cooling fan to clear the new condensor.

Please see below pics and it should give anyone thinking of doing the same a good starting point.

Modified GTR R32 Fan

GTR R32 Custom AC Hose Fitted

Modified GTR R32 Hoses

GTR R32 HOSE

  • 5 months later...

for what its worth, if your going to goto the effort of modifying or making up new lines for an ac system, you may aswell replace the compressor with a universal aftermarket type and just get the lines made to suit, and on the topic of higher pressures, you should have a low and high pressure switch installed to make the ac cut off if pressures get to high, yet a newer style of condenser will cool better so lower pressures a bit more and keep the car ac abit cooler.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...