Jump to content
SAU Community

Recommended Posts

update?

Also, what type of oil and how much did they use?

Can greatly affect the life of the compressor.

Hi Luke,

After inspection, it looks as though the AC compressor had overheated internally and seized.

The A/C specialist suspected the pressure's were too high due to the older original condensor design as the system was not designed to operate on R134a.

We used PAG46 oil in the new A/C compressor. Between 160-180ml.

Did they replace the reciever drier and clean out all the lines? Cause the metal shavings from the first failure will kill a new compressor very fast

Yes they replaced the reciever drier, cleaned out all the lines, even replaced one. Also did the evaporator, TX valve under the dash. Cleaned the lined out with Shellite. The works.

Hi All,

OK so here is the update and where I am up to.

I have 3x GTR R32 A/C compressors. 2x Zexel (original one off the car that leaked and a second hand working one I bought recently) & 1x Valeo (the new one that failed)

The specialist pulled apart all 3 of them and made 1 really good one. Looks like he decided to use the Zexel housing.

180ml of n8 denso oil has been put in it and we fitted it to the car.

Next we have removed the old condenser from the car, drilled out the rivets and removed the mounting brackets to be reworked into a new universal condenser.

The reason for using a new universal condenser is because it was suggested that the pressures with the original condenser was to high after retro fitting with134a gas.

The old condenser was a 'Serpentine' type and the new I bought is a much more efficient 'parallel flow' condenser.

Just waiting for the rain to clear so that we can fit it to the car, then have to clean all the lines again before recharging the system and it should be ready for winter lol.

Pictures to follow..

Edited by paulyp
  • Like 1

Hmmm.

I have a feeling it may be over oiling.

I have run 134a without any issues.

Even in temps as high as 40°.

Do you know how many mls you put in yours?

Paulyp, did you modify your condenser fan to turn on with the air con?

Hi Dark26, Yes that was modified to turn on whenever the air-con was running.

Will check the fan before re-fitting to make sure its still ok.

Do you know how many mls you put in yours?

Hi Dark26, Yes that was modified to turn on whenever the air-con was running.

Will check the fan before re-fitting to make sure its still ok.

cant remember.

Would have been around the 30ml mark.

But, I will check the workshop manual and let you know what Nissan recommend.

  • 4 months later...

Hi all,

Just another update for everyone.

We have finished fitting the AC about 2 months ago and its working well.

Went through alot of effort to fabricate brackets and have hoses made to fit. Also had to modify the standard cooling fan to clear the new condensor.

Please see below pics and it should give anyone thinking of doing the same a good starting point.

Modified GTR R32 Fan

GTR R32 Custom AC Hose Fitted

Modified GTR R32 Hoses

GTR R32 HOSE

  • 5 months later...

for what its worth, if your going to goto the effort of modifying or making up new lines for an ac system, you may aswell replace the compressor with a universal aftermarket type and just get the lines made to suit, and on the topic of higher pressures, you should have a low and high pressure switch installed to make the ac cut off if pressures get to high, yet a newer style of condenser will cool better so lower pressures a bit more and keep the car ac abit cooler.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...