Jump to content
SAU Community

Bits N Pieces=R33 Gtst, R31, Rb30, 100Mm Cooler

SLY-25T
 Share

Recommended Posts

SLY-25T Mentor

SLY-25T

Posted
Posted

Hey All,

So I was gonna go down 25/30 route with the 33 but have decided I'd rather save to buy a house then spend my deposit on the car.

I only purchased the motor and cooler around 6 months ago and since then they have been sitting in my garage awaiting some love and attention.

All items are located in Wattle Grove, Sydney. Near Liverpool. Best contact is mobile SMS- 0401613535.

Not delivering at this time as I honestly CBF and just want it gone without hassles. Cash pickup much preffered.

1. RB30 Head and Block. Out of a R31 as can be seen by NISSAN stamps not HOLDEN. Unknown KM, only bought it to get sent away and get the works done.

$200

post-53838-0-79217500-1361235691_thumb.png post-53838-0-19006200-1361235711_thumb.pngpost-53838-0-00428100-1361235725_thumb.png

2. 600x300x100mm Intercooler with piping to suit Forward facing plenum with high mount on an RB30. Has attachment for water/meth (previous owner explained). Think the piping is to suit MAFLESS too.

$200

post-53838-0-91244900-1361236032_thumb.png post-53838-0-06324200-1361236065_thumb.png

3. RB30 Intake and Exhaust Manifolds. As previously stated, NISSAN not HOLDEN. As far as i know all the hoses are there on the intake. Only thing that should be needed is new gaskets? If I have no interest they will just be binned.

$50 for both?

post-53838-0-97340800-1361236208_thumb.png post-53838-0-14371600-1361236223_thumb.png post-53838-0-15401100-1361236235_thumb.png

4. R33 GTST HICAS unit. Was working in my car, replaced with a lockbar. As above, if no interest I'll just be throwing it out.

$50

post-53838-0-05217200-1361236356_thumb.png

5. RB25DET S1 Coil Pack cover. Prob good if you wanna muck around painting or cutting and customising.

$20

post-53838-0-14296700-1361236456_thumb.png

6. R33 GTST S1 rear strut brace. Just Jap brand. Looks to be a lil twisted but i was still able to fit it. Had alot of fuel pump issues so had enough of constantly having to take it off and back on.

$30

post-53838-0-31200000-1361236564_thumb.png

7. Excedy Heavy Duty clutch to suit R33 GTST S1 (Push?) worn out. Suit rebuild, was looking at sending away to rebuild but a clutch came up cheap.

$150?

post-53838-0-11436300-1361236675_thumb.png

As metioned, I'm not willing to post atm. Rather it get picked up and clear out my garage.

Best contact is by mobile SMS.

If most parts arent sold they will most likely be thrown out.

Throw me some offers.

Thanks,

Jaye

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      ECU sees many times the speed than speedo does (R34 swap)

      By Kapr · Posted

      Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...