Jump to content
SAU Community

Recommended Posts

I thought it was about time I added some of the detail about my project, I have a Mr30 Ti Skyline with a Rb25det conversion. Below is a brief list of improvements I have done over the last few years

Long nose R200 with Detroit locker and Z31 drive shafts

Full 3in exhaust

Replaced all the rear end bushes to keep it in a straight line

Minor tuning/ boost increase with standard engine management to keep it interesting

Added the all important stereo

Eboost street

Z32 brake master cylinder and booster

S13 coil over conversion with brake upgrade

Then things started to get serious with a GTX3076r

850cc injectors

Forward facing plenum with Q45 TB

Front mount Cooler

Splitfire coils

Under car surge tank with 044

Nistune by Status

Quaife centre for the diff

After all that I hit a wall with the standard manifold at 270RWKW and then started to break drive shafts and the clutch was slipping on maximum abuse so, this is where I'm at today

Hybrid low mount manifold sitting on the bench ready to go in once I upgrade the drive shafts

Waiting on parts to make a set of custom shafts with commodore CV's

Installing a built manualised auto with pro ratchet shifter.

I will dig through all the photos to keep it interesting, lots of quality shed time is invested into the ongoing build so far and lots more to come.

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/
Share on other sites

  • 4 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 2 months later...

Been busy lately and ordered a few bits

Precision turbo inter cooler

Upgraded tailshaft

Aes muffler

Air temp and transmission temp gauge

And a few other bits to stop the trans fro leaking

The cooler arrived and looks very nice. I will put up some nice photos later

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/#findComment-6953531
Share on other sites

  • 3 weeks later...

Been busy lately and ordered a few bits

Precision turbo inter cooler

Upgraded tailshaft

Aes muffler

Air temp and transmission temp gauge

And a few other bits to stop the trans fro leaking

The cooler arrived and looks very nice. I will put up some nice photos later

Muffler done. I remover two chambered 3in mufflers and put the Aes 3in in and it's quieter and straight through. Can't say enough good things about this muffler and no drone

Cooler to go in on Monday can't wait. My intake temps are 35deg on a 14deg day

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/#findComment-6986206
Share on other sites

Muffler done. I remover two chambered 3in mufflers and put the Aes 3in in and it's quieter and straight through. Can't say enough good things about this muffler and no drone

Cooler to go in on Monday can't wait. My intake temps are 35deg on a 14deg day

post-84952-13777292666354_thumb.jpg

Cooler done. Intake temps only move by a few deg now instead of the 30 deg variance with the old one

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/#findComment-6992923
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...