Jump to content
SAU Community

Recommended Posts

I thought it was about time I added some of the detail about my project, I have a Mr30 Ti Skyline with a Rb25det conversion. Below is a brief list of improvements I have done over the last few years

Long nose R200 with Detroit locker and Z31 drive shafts

Full 3in exhaust

Replaced all the rear end bushes to keep it in a straight line

Minor tuning/ boost increase with standard engine management to keep it interesting

Added the all important stereo

Eboost street

Z32 brake master cylinder and booster

S13 coil over conversion with brake upgrade

Then things started to get serious with a GTX3076r

850cc injectors

Forward facing plenum with Q45 TB

Front mount Cooler

Splitfire coils

Under car surge tank with 044

Nistune by Status

Quaife centre for the diff

After all that I hit a wall with the standard manifold at 270RWKW and then started to break drive shafts and the clutch was slipping on maximum abuse so, this is where I'm at today

Hybrid low mount manifold sitting on the bench ready to go in once I upgrade the drive shafts

Waiting on parts to make a set of custom shafts with commodore CV's

Installing a built manualised auto with pro ratchet shifter.

I will dig through all the photos to keep it interesting, lots of quality shed time is invested into the ongoing build so far and lots more to come.

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/
Share on other sites

  • 4 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 2 months later...

Been busy lately and ordered a few bits

Precision turbo inter cooler

Upgraded tailshaft

Aes muffler

Air temp and transmission temp gauge

And a few other bits to stop the trans fro leaking

The cooler arrived and looks very nice. I will put up some nice photos later

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/#findComment-6953531
Share on other sites

  • 3 weeks later...

Been busy lately and ordered a few bits

Precision turbo inter cooler

Upgraded tailshaft

Aes muffler

Air temp and transmission temp gauge

And a few other bits to stop the trans fro leaking

The cooler arrived and looks very nice. I will put up some nice photos later

Muffler done. I remover two chambered 3in mufflers and put the Aes 3in in and it's quieter and straight through. Can't say enough good things about this muffler and no drone

Cooler to go in on Monday can't wait. My intake temps are 35deg on a 14deg day

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/#findComment-6986206
Share on other sites

Muffler done. I remover two chambered 3in mufflers and put the Aes 3in in and it's quieter and straight through. Can't say enough good things about this muffler and no drone

Cooler to go in on Monday can't wait. My intake temps are 35deg on a 14deg day

post-84952-13777292666354_thumb.jpg

Cooler done. Intake temps only move by a few deg now instead of the 30 deg variance with the old one

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/#findComment-6992923
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...