Jump to content
SAU Community

Recommended Posts

I thought it was about time I added some of the detail about my project, I have a Mr30 Ti Skyline with a Rb25det conversion. Below is a brief list of improvements I have done over the last few years

Long nose R200 with Detroit locker and Z31 drive shafts

Full 3in exhaust

Replaced all the rear end bushes to keep it in a straight line

Minor tuning/ boost increase with standard engine management to keep it interesting

Added the all important stereo

Eboost street

Z32 brake master cylinder and booster

S13 coil over conversion with brake upgrade

Then things started to get serious with a GTX3076r

850cc injectors

Forward facing plenum with Q45 TB

Front mount Cooler

Splitfire coils

Under car surge tank with 044

Nistune by Status

Quaife centre for the diff

After all that I hit a wall with the standard manifold at 270RWKW and then started to break drive shafts and the clutch was slipping on maximum abuse so, this is where I'm at today

Hybrid low mount manifold sitting on the bench ready to go in once I upgrade the drive shafts

Waiting on parts to make a set of custom shafts with commodore CV's

Installing a built manualised auto with pro ratchet shifter.

I will dig through all the photos to keep it interesting, lots of quality shed time is invested into the ongoing build so far and lots more to come.

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/
Share on other sites

  • 4 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 2 months later...

Been busy lately and ordered a few bits

Precision turbo inter cooler

Upgraded tailshaft

Aes muffler

Air temp and transmission temp gauge

And a few other bits to stop the trans fro leaking

The cooler arrived and looks very nice. I will put up some nice photos later

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/#findComment-6953531
Share on other sites

  • 3 weeks later...

Been busy lately and ordered a few bits

Precision turbo inter cooler

Upgraded tailshaft

Aes muffler

Air temp and transmission temp gauge

And a few other bits to stop the trans fro leaking

The cooler arrived and looks very nice. I will put up some nice photos later

Muffler done. I remover two chambered 3in mufflers and put the Aes 3in in and it's quieter and straight through. Can't say enough good things about this muffler and no drone

Cooler to go in on Monday can't wait. My intake temps are 35deg on a 14deg day

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/#findComment-6986206
Share on other sites

Muffler done. I remover two chambered 3in mufflers and put the Aes 3in in and it's quieter and straight through. Can't say enough good things about this muffler and no drone

Cooler to go in on Monday can't wait. My intake temps are 35deg on a 14deg day

post-84952-13777292666354_thumb.jpg

Cooler done. Intake temps only move by a few deg now instead of the 30 deg variance with the old one

Link to comment
https://www.sau.com.au/forums/topic/420762-mr30-sleeper/#findComment-6992923
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
×
×
  • Create New...