Jump to content
SAU Community

Recommended Posts

Up for grabs is this kit for my skyline which i have now sold without this kit installed so its now sitting in my shed gathering dust.

This kit is 100% bolt on and consists of the following:

4 piston Alcon Grex calipers front and back

356x32mm 2 piece Greddy front rotors with DS2500 pads (bout 60-70%)

315x32mm rear rotors with Pagid blues pads (bout 80- 90%) .

I had the kit powder coated by Craved coatings and were disassembled and rebuilt with fresh seals by Specialized brakes in Penrith. The Kit is complete except for brake lines BUT my HEL brake lines screwed straight into these with just the use of a copper washer. Rotors appear to have plenty of meat left on them I will measure them with a Vernier for potential buyers :thumbsup:

Would prefer local pick up but will ship interstate also

$4000ono

Freshly powdercoated before assembly

20120714_155132.jpg

Fronts assembled

20120726_182227.jpg

Link to comment
https://www.sau.com.au/forums/topic/420892-alcon-grex-greddy-big-brake-kit/
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

That pic was taken when the kit 1st arrived home and literally as soon as it was unpacked hence the grubby old colour of them for those wondering.

Contact Mick 0423089277 if you wanna know more :thanks:

Also for those wondering, the front will fit under 17s but not all. They fit under drifteks, advan t5s and TE37s, as I have the same kit.

GL with the sale. Sick brakes!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...