Jump to content
SAU Community

Recommended Posts

Hey guys,

Need to take off timing belt, and hence need to take off the bottom pulley.. problem is the damn bolt isnt budging. I have put the car in gear but it still has give so the engine is turning instead of the bolt being undone... anyone have any tips... also, what size is it exactly.. i think my socket my be 1mm too big.

dave.

Link to comment
https://www.sau.com.au/forums/topic/42132-removing-bottom-pulley-on-rb25/
Share on other sites

dave , its 27mm and its very tight , you need a long bar , put the car in gear and pull handbrake up then use your arm mate . if you cant get it that way you can use the starter , this is how . put socket in place with the bar and make sure the bar will hit the rail ( left one ) when you hit the starter .another way is to take the starter off and put a strong screwdriver in the ring gear the get someone to undo the nut .i hope you know when you get the nut undone you need a gear puller to pull the pulley off , its got the 2 holes there for that reason so you need 2x 6 mm bolts

dave , does the car move forward when u have h/brake on and in gear ? if yea get someone to press the brakes , you still will get the engine to turn a little but you should be able to undo it . as for the ring gear you have to take the starter out first and be carefull not to brake any teeth . you may want to try undoing it with the starter though read above how to do it .

good luck ,

cheers , jerry

Dave get someone to hold the bottom pulley with the hand brake on and put it in gear you must use a long breaker bar (350mm) or larger if you are to have any chance at getting it loose.If not your timing belt might just flex under the strain getting you nowhere.sidchrome make them allong with many others. :P

Dave,

Get yourself about 1 meter of 10mm blue nylon (plypropylene) rope, fold it in two and pass the two ends through the loop so you have a choker.

Place the choker end around the crank pulley where one of the belts go, and knock it down tight so it pulls against the direction you are trying to run the nut. It should be pulling back against itself so as to always be tightening against you.

Take the two loose ends, and make a double hitch around the water pump housing.

Get your breaker bar, and marvel at how easily it comes undone ;)

  • 7 months later...

HEY everyone, This sort of relates to this thread.

What are all your methods for tightening the crank pulley? Using the hand brake seems to put way to much strain on the cables/shoes or something and as i tighten the car is trying to creep forward so the crank isnt staying still. Even with someone in the car pressing hard against the brakes there is just wind up in the drive train and it isnt locking the crank. Any ideas??????????????

Ok, lets start with a few tihngs...

1. if you do the rope idea you'll screw the bearings in the alternator or you'll bugger the seal in the water pump. and anyway, if you've got a breaker bar you'll be able to do it ten times easier with the starter motor.

2. don't bother with the screw driver in the flywheel/flexplate coz that'll just sh1t you tryin to get it back in, and out for that matter.

3. unless you have a breaker bar you'll never get it off with someone standing on the brakes with handbrake and in gear in which case you can do it ten times easier with the starter motor.

4. NEVER turn the crank with the car in gear and handbrake on coz you'll pop your gearbox and then car a no go.

Ultimately, unless you got a rattle gun and a compressor or a breaker bar you aint gonna get it off unless you are really lucky.

Best idea is with the breaker bar and a pipe over the end put the 27mm socket over the bolt and put the pipe over the breaker bar and hold it hard up against the left chassis rail. Get someone to crank the starter motor (not full cranks as if you were going to start it but just enough to crack the bolt). Make sure you hold the socket onto the nut and don't let go. Don't worry, as long as you hold it, it shouldn't bite you.

Or basically the way wrxhoon described it. (Sorry to repeat your advice)

But it is the best way.

Ok, lets start with a few tihngs...

1. if you do the rope idea you'll screw the bearings in the alternator or you'll bugger the seal in the water pump.

Correct, which is why I said......
Kinda like this, but don't use the alternator, put it around the water pump housing so not to damage anything.
:rofl:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...