Jump to content
SAU Community

Recommended Posts

Hey guys,


Looking at changing up my daily car. The GTR has been fun but need something different as well all know circumstances have changed. This is an expression of interest as I need the money to fund the next car purchase.

The Car:

Fairly stock, it has an Apexi Power FC with hand controller, Greddy Profec B II Boost Controller, RS*R exhaust, Rear GT wing, DTM 18" Rush shadow chrome rims, Adjustable caster rods, Sparco Racing drivers seat.

It has done a touch over 150,000kms, serviced every 5000km. The paint work on it isnt very strong, but its the only thing wrong, and only a few places need to be touched up.

I am willing to answer any questions via PM as im not always at my phone.

I am asking $13500 for it.

Car is in Greater Western Sydney

Cheers

post-87170-0-70442000-1363069985_thumb.jpg

post-87170-0-36709500-1363070005_thumb.jpg

post-87170-0-04482600-1363070054_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/421525-eoi-1990-nissan-skyline-gtr/
Share on other sites

  • 1 month later...

Price dropped to $12,800.

And will throw in all my spare parts with it. Good upgrade parts.

Please contact me also on 0400629822, sms as not always next to my phone.

http://www.carsales.com.au/private/details/nissan-skyline-1990-14724074?base=&vertical=Car&cr=0&eapi=2&__N=1246%201247%201252%201282&find=yhs33j|CarRego&silo=Stock&num=15&sort=default

Bump

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...