Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

ATM the exhaust is just cat back how big would you go the whole way through?

What's the diametre size of your car back?

If it's a 3", then go 3", if it's a 3.5" go 3.5" etc...

​Keep it consistent.

What N1 turbos you getting?

From memory they came from factory running about 1 Bar = 14.7 Psi.

(R32 GTR Nismo & N1 / R33 GTR N1 / R34 GTR V-Spec N1 & V-Spec II N1 / V-Spec II Nur / M-Spec Nur)

You could run a tad higher 1.1 Bar = 15.9 Psi / 1.2 Bar = 17.4 Psi.

What do you recommend? I'm open minded. Honestly, I was thinkin of purchasing the Garrett equivalents as I official N1 turbos would be pricey.

What's the diametre size of your car back?

If it's a 3", then go 3", if it's a 3.5" go 3.5" etc...

​Keep it consistent.

I thought these cars needed a little back flow. Having the whole exhaust the same size would not promote that.

What do you recommend? I'm open minded. Honestly, I was thinkin of purchasing the Garrett equivalents as I official N1 turbos would be pricey.

Yes, genuine N1 turbos would be pricey at the same time rare to find.

Garrett -7's would be the closest to the N1 equivalents.

I am running Garrett -7's with 15.5 Psi, which is just over 1 Bar.

Later I will run about 18 Psi = 1.2 Bar, but will get my mechanic to see what he thinks best.

Many factors are involved but you'd run what's safe for the engine / what the turbos can handle, so when you go in for a tune after the twin turbo installation, your mechanic should be able to gauge what it can run.

I thought these cars needed a little back flow. Having the whole exhaust the same size would not promote that.

Not that I know of... That theory might apply to N/A cars... As you can only go so big unless it's tuned for it...

With turbocharged cars, usually the bigger the better, but 3" / 3.5" is usually the upgrade we all go for and it frees up the exhaust flow.

:)

​Just in regards to your bigger front mount intercooler, you were better off spending the money on Down and Front Pipes with a High Flow Cat.

Giving your GTR a full exhaust upgrade will benefit you more at this stage, if you just want to keep it stock-ish...

Stock GTR front mount intercooler can handle 300+ kW's.

But anyway, all for the better in the long run.

I know it'll do 400+ kW's for a fact as well ;)

What's the diametre size of your car back?

If it's a 3", then go 3", if it's a 3.5" go 3.5" etc...

​Keep it consistent.

I apolagize it has a 3.5 inch all the way through just had a look before with that and a bigger intercooler does that add any more hp with out a tune? Just curious cause next step is a bigger fuel pump, injectors, tune and ecu yeah?

I know it'll do 400+ kW's for a fact as well ;)

:laugh: yes clearly, you would know!

Good and thanks for clarifying that!

I apolagize it has a 3.5 inch all the way through just had a look before with that and a bigger intercooler does that add any more hp with out a tune? Just curious cause next step is a bigger fuel pump, injectors, tune and ecu yeah?

So your exhaust is all good then!

Depends on what power out put you want... How many kW's you want?

Which determine if you need a bigger fuel pump / injectors / ECU / Tune or not...

:laugh: yes clearly, you would know!

Good and thanks for clarifying that!

So your exhaust is all good then!

Depends on what power out put you want... How many kW's you want?

Which determine if you need a bigger fuel pump / injectors / ECU / Tune or not...

I'm looking for 350 hp at the wheels..... So im guessing I need a fair bit

I'm looking for 350 hp at the wheels..... So im guessing I need a fair bit

Which is about 261 rwkW's.

You stock injectors / fuel pump / ECU can handle it.

The ECU will need a slight tweak but nothing crazy.

What ecu were you running?

Run a Nistune or an APex'i Power FC.

Id say that you will very quickly get bored of 250kw. So i would recommend a link ecu. I shouldve skipped the power fc stage and gone straight to a link

What link will you reccommend? Shouldn't get bored to quick as I'm only used to driving a vz sv6 haha

I'm looking for 350 hp at the wheels..... So im guessing I need a fair bit

Which is about 261 rwkW's.

You stock injectors / fuel pump / ECU can handle it.

The ECU will need a slight tweak but nothing crazy.

What ecu were you running?

Run a Nistune or an APex'i Power FC.

What's the highest stock whp that can be SAFELY achieved using stock components and N1 turbos?

Sent from my SC-03D

What's the highest stock whp that can be SAFELY achieved using stock components and N1 turbos?

Sent from my SC-03D

To be safe for street use, anywhere around the 300kW mark at the rear wheels.

Two friends of mine on SAU are running stock RB26's but one has Garrett -7's and the other has Garrett -9's

Both making 300rwkW's, which is about 402HP at the wheels, if you want to measure in HP.

You could push it further but it will depend on the condition of the engine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...