Jump to content
SAU Community

Recommended Posts

Licensed 1990 R32 GTR gun metal grey that I personally imported from Japan in 2005. The car is licensed and comes with 6 months WA rego and was always well maintained with Motul oils and was tuned by Hyperdrive. I decided to sell the project due to poor health.

Since owning the GTR I had done a few modifications and decided to strip the engine bay etc for a full respray when some person decided it would be a good idea to key it all over. At the moment the engine , gear box and engine bay components have been taken out ready for a respray, all interior is still in place. The body is rust free.

The engine had no issues when it was in the car and had about 160psi in all six pots.

Modifications done so far are as follows:

Engine:

  • Tomei Type B 260 cams
  • Tomei cam caps
  • Sard 700cc injectors
  • K&N pod filters and pipe work
  • Spitfire coils
  • Garret 2860-5 turbos
  • Sard Ali racing radiator
  • Sard fuel regulator
  • Full Monty clutch
  • Trust intercooler
  • New CV joints and boots
  • Bosch 044 in tank fuel pump



Brakes & Wheels


Fully rebuilt front brake callipers
Stock R32 GTR Rims
New Brake Lines
Tein Super Street Coilovers
Nismo clutch slave

Electronics

Apexi Power FC and Hand Controller
Blitz Dual solenoid EBC has LCD display
Full White Nismo Dash & centre console


Not Yet Fitted

New rubbers, badges, seals and mouldings for whole car ( Over 2.5K+ alone)
Complete engine seal and gasket kit.
Spare front seats
New silicone hose set for engine

New genuine hose set for engine
Kakimoto dual exhaust
R34 Dump pipes ( better flowing then stock R32 items) "photo not taken yet"
Tomei 2mm oil restrictor
Fully refurbished R32 gear box "photo not taken yet"
Mines Baffle kit "photo not taken yet"
Tomei sump baffle kit "photo not taken yet"
GREX oil pump

6Boost Manifold for single top mount

New Garrett Gtx3582R

Nismo engine mounts

New handles

New handle surrounds

2.8L Fardon Stroker crank ( where HKS got their cranks ) Step two crank

Apexi intake kit

Arp head and engine bolts

ATI 1000hp balancer and pulley kit

Carbon fibre rear strut

DBA 4000 rotors

FC data logit

Pauter rods

new set of tein coilovers

And anything else I missed from list.

That's all I can remember for now. Car was never tracked, taken to drags or thrashed.
Chasing for whole package is $17,000.

NO SWAPS NO TRADES NO PARTING OUT

Rob 0413 670 040 or email [email protected]

post-25605-0-20721000-1363580958.jpg

post-25605-0-26953700-1363580965_thumb.jpg

post-25605-0-95457100-1363580965.jpg

post-25605-0-35765100-1363580966.jpg

post-25605-0-94447700-1363580966.jpg

post-25605-0-61396500-1363580967.jpg

post-25605-0-25812000-1363580968.jpg

post-25605-0-67544100-1363580968.jpg

post-25605-0-70361200-1363580969.jpg

post-25605-0-53092400-1363580970.jpg

post-25605-0-80544100-1363581043.jpg

post-25605-0-27797700-1363581044.jpg

post-25605-0-70706100-1363581044.jpg

post-25605-0-23036100-1363581045.jpg

post-25605-0-71883300-1363581045.jpg

post-25605-0-31011900-1363581046.jpg

post-25605-0-06429000-1363581048.jpg

post-25605-0-06877700-1363581049.jpg

post-25605-0-67133800-1363581049.jpg

post-25605-0-65716700-1363581050.jpg

post-25605-0-06956900-1363581142.jpg

post-25605-0-07699200-1363581143.jpg

post-25605-0-26692500-1363581145.jpg

post-25605-0-48562300-1363581146.jpg

post-25605-0-56830200-1363581147.jpg

post-25605-0-60579900-1363581148.jpg

post-25605-0-81894500-1363581149.jpg

post-25605-0-91344300-1363581150.jpg

post-25605-0-99766100-1363581151.jpg

post-25605-0-09902000-1363581153.jpg

post-25605-0-49748200-1363581210.jpg

post-25605-0-87492300-1363581210.jpg

post-25605-0-75364300-1363581211.jpg

post-25605-0-58014600-1363581212.jpg

post-25605-0-97435800-1363581212.jpg

post-25605-0-53195000-1363581213.jpg

post-25605-0-99473000-1363581213.jpg

post-25605-0-10782000-1363581215.jpg

post-25605-0-88166200-1363581215.jpg

post-25605-0-68186500-1363581216.jpg

post-25605-0-88014800-1363581314.jpg

post-25605-0-21993500-1363581315.jpg

post-25605-0-73827000-1363581315.jpg

post-25605-0-16258200-1363581316.jpg

post-25605-0-55888900-1363581316.jpg

post-25605-0-12232000-1363581317.jpg

post-25605-0-51609100-1363581317.jpg

post-25605-0-98197200-1363581317.jpg

post-25605-0-39342000-1363581318.jpg

post-25605-0-89881200-1363581318.jpg

post-25605-0-34652400-1363581357.jpg

post-25605-0-73246000-1363581357.jpg

post-25605-0-14937100-1363581358.jpg

post-25605-0-69046300-1363581358.jpg

post-25605-0-10314100-1363581359.jpg

post-25605-0-62224900-1363581359.jpg

post-25605-0-01875400-1363581360.jpg

post-25605-0-58515400-1363581360.jpg

post-25605-0-01743000-1363581361.jpg

post-25605-0-56445200-1363581361.jpg

post-25605-0-26678000-1363581380.jpg

Link to comment
https://www.sau.com.au/forums/topic/421870-r32-gtr-unfinished-project/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...