Jump to content
SAU Community

Recommended Posts

Updating parts list all the time as I find things so keep an eye on the first post. Many parts are not listed yet so just ask as I probably have it.

Prices are ONO so don't hesitate to make fair offers, it's all gotta go!

Located in lower Blue Mountains Sydney, can post/courier most things at cost.


S2 Rs4s Stagea- White

Front drive shafts $130 each
Front hubs $120 each
Manual gearbox $850 (2001 model, has gear stick)
Manual conversion $500 (pedals, handbrake, master/slave, flywheel, clutch and slave)
Manual dash cluster $150
Manual steering wheel with airbag $200
Head lights $350 (no fading)
Radiator (manual) $200
Steering rack and lines $150
Crossmember $100
Dash $100
Passenger airbag $100
Glove box $40
Bonnet $100
Boot with wing $180
Doors $100 each
Front guards $80 each
Brakes $100
ABS unit $100
Strut brace $50 (is slightly bent where another front cut was stacked on top of it)
Front reo $80
Fog lights $60

Neo Rb25det motor parts (parting out due to low compression on number 6):

-Head including covers and complete intake, no turbo $Sold

-Turbo $400

-CAS- sold

-Sump $250

-Block $300

-Spitfire coilpacks $280

-S2 (pink label) AFM $80 plug not included

-Engine loom $150



S1 Rs260 Stagea- white

Interior door trims (RS260 trim) $300 for all four
Front and rear seats (RS260 trim) $TBA depending on condition when I check them out
Complete rear end minus diff and with 32gtr brakes not brembos (sold already) $500
Passenger side headlight $100
Dolphin side skirts and rear bar $250 for both (rough condition)
Rear wing $50
Drivers window switches $80
Passenger window switch $30
Intercooler (stock) $150
Radiator $100
Tail lights $50 pair
Bonnet gas struts $40 pair
Bonnet hinges $30 pair
Front door hinges $30 for the lot
Catch can $20

Dolphin Side skirts and rear bar $120 each, they are in average condition and could do with minor repairs. No postage local pick up only on these (they cost a bomb to send).

Various other parts to be uploaded as I go.

Remember prices are ONO!

post-219-0-48400500-1369282052_thumb.jpg

post-219-0-79920800-1369282054_thumb.jpg

post-219-0-78613400-1369282058_thumb.jpg

post-219-0-00531500-1369282068_thumb.jpg

post-219-0-66531100-1369282070_thumb.jpg

post-219-0-23749600-1369282077_thumb.jpg

post-219-0-40302700-1369282164_thumb.jpg

post-219-0-32850800-1369282167_thumb.jpg

post-219-0-97036000-1369282170_thumb.jpg

post-219-0-51429500-1369282177_thumb.jpg

post-219-0-43745700-1369282180_thumb.jpg

post-219-0-34963700-1369282212_thumb.jpg

post-219-0-91460200-1369282214_thumb.jpg

post-219-0-28528400-1369282217_thumb.jpg

post-219-0-02770700-1369282226_thumb.jpg

post-219-0-98968500-1369282227_thumb.jpg

post-219-0-36159400-1369282230_thumb.jpg

post-219-0-26011800-1369282233_thumb.jpg

post-219-0-82442200-1369282235_thumb.jpg

post-219-0-84254800-1369282238_thumb.jpg

post-219-0-49438900-1369282241_thumb.jpg

post-219-0-62892400-1369282247_thumb.jpg

post-219-0-67393500-1369282249_thumb.jpg

post-219-0-93714000-1369282251_thumb.jpg

post-219-0-15638800-1369282256_thumb.jpg

post-219-0-56314600-1369282258_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...