Jump to content
SAU Community

Recommended Posts

hey everyone im parting out my r33 skyline gtst rb25det i have owned this car now for a few years and know its time to let it go has run out of rego and cant be bothered getting it back on the road so have decided to part it out if you need any parts let me know and ill give you a price call or text on 0432-062-780

rb25det motor loom and ecu and with aftermarket coilpacks $1600

brakes rotors hubs awsome for 5 stud conversion $550

r33 gtst diff $200

headlights $400 for both

blitzs wheels $700 255 rear 235 on the front

bonnet $150

guards $100 ea

king springs super lows $150

factory option a pillars with inbuilt tweeters

for anything else call or text on 0432-062-780

located in Melbourne

post-62515-0-79709200-1370134131_thumb.jpg

post-62515-0-36627800-1370134167_thumb.jpg

post-62515-0-49673600-1370134402_thumb.jpg

post-62515-0-96349500-1370134442_thumb.jpg

post-62515-0-39259600-1370134463_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/426251-r33-gtst-partout/
Share on other sites

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...