Jump to content
SAU Community

Recommended Posts

OK i dont know much about engines so i will try and explain this to you guys.

I was changing my plugs the other day and when I took the big metal pipe that crosses over where the plugs are in, there was a small amount of oil in the pipe and I am pretty damn sure there shouldnt be.

Do you know what this is from and how bad is it.

Link to comment
https://www.sau.com.au/forums/topic/42634-what-could-this-be-from/
Share on other sites

Sounds like excessive crankcase ventilation.

I understand it as follows - as you wind in more boost or your rings become worn pressure from the combustion process will pass the rings and enter the crankcase. From here the excess pressure breathes from the rocker covers into the induction piping (or in extreme cases from your dipstick hole). Most will get caught in the intercooler but some will make it the plenum. If its only a small amount it should be fine but installing a catch can between the rocker cover vent and the induction piping will prevent most oil from i) entering the combustion process which can cause detonation ii) clogging your cooler and restricting flow. Its an indication your motor is becoming tired but i've also seen tight motors breath heavy if you dial in enough boost.

Worst case scenario would be broken ringlands and/or rings.

Yeh its nothing ben,

Awhile ago when i was running 12psi most of the time it was getting a bit of oil in the throttle body, now that its on standard boost, i havent seen any oil in the last 2 spark plug changes.

Im jus getting a catch can, easiest way to combat it.

i have something related to this in my rb25 silvia i recently bought, the oil is in the intercooler piping from turbo to intercooler (maybe other side, not sure).

from reading this im guessing oil on the engine side of intercooler isnt too bad, but turbo side (unless it came from engine?) is worse?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...