Jump to content
SAU Community

Recommended Posts

Hi guys, recently my R33 GTR's battery warning light started flashing and now remains permanently on when the car runs fine and shows no signs of stalling or drained of power. What's going on and how to fix?

Firstly, I had the car at a motor mechanic for a couple of months where it was hardly driven each day so is the battery dead? This battery was brand new and only replaced 5 months ago. Ever since taking the car home, it's been on a trickle charger and only driven monthly but the charger does indicate that the battery has been fully charged so not sure why this is happening.

Recently, my amp/sub combos earth wire going from the "control" went loose so I had to fix and it sparked a few little sparks which is normal so not sure if this had anything to do with it. I assume not ?

Any help would be much appreciated.

alternators have 2 circuits. one for charging and one for the warning light. sounds like the warning light circuit may be faulty. get a multimeter and check the charging voltage on the battery terminals to be sure the alternator is charging correctly

The warning light is a part of the excitation circuit through the regulator.

The regulator is most likely on the way out.

When that circuit fails the alternator stops producing charge as there is no excitation current to produce an electro-magnetic field inside the armature.

Update: so the problem got worst. Slowly the battery just won't hold charge anymore and eventually I found myself stuck in the middle of the road with no power so it's at a friends house now.

You guys think the alternator is home or more the battery dead?

I'm leaning more toward the battery.

Alternator for sure.

The tell tail signs are there.

The battery warning lamp was coming on notifying you that the alternator was starting to fail. Eventually it did completely fail and the entire car from that point on ran off the battery which then lead to a complete flat battery and your car stuck in the middle of a road.

Replace the alternator, stick the battery on charge for 24 hours and you should be good to go.

Thanks guys. Really appreciate it. I will get it looked at by a mechanic this weekend. Hopefully this will serve as a lesson for others.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...