Jump to content
SAU Community

Recommended Posts

AFTERMARKET PARTS:

2 BLITZ turn flow coolers also available with piping to suit R32 and R33.

HKS HYPER-D fully adjustable coilovers for R34

Slotted and drilled rotors for R34

Height and damper coilovers for R33 available will check brand tomorow.

Spitfire coilpacks for S1 R33

Strut braces for R33 and R34 front and rear,

Rear cusco strut brace for S13

the big VG30 turbo available ( not aftermarket i know )

Z32 AFM with plug ( Genuine item )

Carbon Fiber air divider for s14

Nismo thermostat for SR20

2x BLITZ dual SBC available with loom and solenoids

Nisstune for SR20DET

Q45 AFM

Greddy EBC with loom and solenoid

ill post more if i remember what else i have,

HAPPY TO PUT ON EBAY FOR INTERSTATE BUYERS

Link to comment
https://www.sau.com.au/forums/topic/427533-edited-admin/#findComment-6903039
Share on other sites

Closed.

Wrecking over 10 cars sounds is a business or a serious backyard operation.

If you wish to trade here on SAU you are required to become paying trader just like everyone else.

More details can be found here:

http://www.skylinesaustralia.com/forums/topic/294953-are-you-a-business-want-to-advertise-on-sau-click-here/

This does not mean you continue sales via PM.

Link to comment
https://www.sau.com.au/forums/topic/427533-edited-admin/#findComment-6903978
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • A little more work this week.  Fitted astra power steering pump in the boot with a lowe fabrication bracket. Gave the pump a good clean, fitted Anderson plug and high pressure fitting. With the intercooler being flipped under rad support factory headlights weren't going to work. Ordered a set of origin battle lights, they arrived so got them test fitted. Will require some fiddling to fit nice but was an easy quick option for now. And today we pulled out the manual Rb gearbox and test fitted a ZF 8HP50. It will fit with some casting tabs cut off and small tap of the tunnel with a hammer. Pick up the adapter plate Wednesday so hopefully all bolted in Friday and measure for tailshaft which will be a 2 piece. Been doing a lot of ecu, pdm and tcu loom design so when comes to wiring it in a few weeks will all go smoothly.
    • FYP. Sadly. Even bolt cutters wouldn't take 2 sec. But in the days of 18v angle grinders, nothing is safe.
    • One piece driveshaft I would recommend a dual CV setup otherwise stick to OEM. I have heard most one piece driveshafts cause excess vibration otherwise. The transmission grind I'm quite familiar with. You can try shockproof gear oil, otherwise you need a new transmission. The shifter is extremely simple on these cars. If you want pull apart the assembly and replace the plastic bushing but I doubt that fixes anything. The tail light issue is very common, unfortunately new tail lights are long discontinued. The trunk antenna going up always is because your radio doesn't have a true power antenna control, just remote amp power signal. There is a blank switch plate that you can pop out and install a switch for this or alternatively source a head unit that has proper antenna control. Throttle body sticking you have to disambiguate by disconnecting the cable and seeing if the linkages are the problem or something else. There is a procedure to adjust them, refreshing them is also somewhat involved if that's the issue. I have dealt with many of these issues. Old cars really are fractals of problems. The more you fix the more you discover there is to fix.
    • Welp, you've got a long list of experiences right there. I'd say you're on the right path.
    • That's correct, suits my requirements a bit better. Sure there are also numpties there, however it's generally a different vibe and more my kind of vibe.
×
×
  • Create New...