Jump to content
SAU Community

Recommended Posts

My A31 (1993 SE-4) has always done this thing where once the car starts moving it fires the central locking and locks all the doors, except the drivers. It's always annoyed me a little bit but not enough to do anything about it.

Unfortunately this system seems to have developed a fault, if you attempt to unlock one of the doors it instantly locks it again. It appears that the door lock actuator is being fired continually which I imagine is going to wear them out sooner or later.

I'd like the keep the central locking working, but disable this one specific feature, is there any way to do that?

Link to comment
https://www.sau.com.au/forums/topic/428384-disabling-the-automatic-door-lock/
Share on other sites

sounds similar to what the new Hyundai's do where all the doors lock after 15km/h it's part of the safety and i believe it can be disabled at the service department.. not sure if that's of any help but i'd take it to someone that knows their way around a locking system.

Chris Rogers for instance.

It's a factory feature, it's not a fault & it's not constantly firing, the master unit for the central locking detects when the locks actuate and will try to lock them again.

They won't 'wear down' over time because of this.

If anything, trying to manually unlock the door while moving will wear our parts, hitting the button on the driver's door probably doesn't do much good either.

I know of one dude that ended up with a bent door lock actuator rod from a passenger trying to constantly override it.

Central locking is controlled by the passenger side power window switch (it's built in)

Other than removing your speedo, or removing your central locking and/or passenger's power window switch, I don't know of any way to remove it.

You could get someone else to drive, , unplug the passenger window switch and use a multimeter to look for a signal that comes on around 10kmp/h (often 15 or 20kmp/h with older/stretched speedo cables), theoretically there's a wire off the dash that triggers something inside that switch to lock all the doors.

Don't know if it's a simple as cutting one or two wires and if that'll cause other issues, but if you're that desperate to get rid of it, it's worth a shot.

Had a look but apparently my search abilities suck, not helped by the fact that all the results for "lock" are about steering, probably also not helped by my lack of knowing Australian English.

The reason this came about is my GF managed to get her hair trapped in the door and didn't notice until I was joining the motorway, when she unlocked the door the dam thing fought back hard enough that it bent her fingers back.

The car will only lock the passenger doors, not the drivers side....so, the safest place for your girlfriends hair is probably in your lap....just saying....

Why was her hair near the lock anyway? that's a mile away from the headrest.....

Windy day and her hair is waist length so easy to trap it when closing the door, hell I manage to shut my own hair in the door sometimes and mine's only armpit length. I usually notice before reaching a sufficient speed for the doors to auto lock.

As for your other suggestion, while it has appeal it would be somewhat easier if I were a bloke :P

Windy day and her hair is waist length so easy to trap it when closing the door, hell I manage to shut my own hair in the door sometimes and mine's only armpit length. I usually notice before reaching a sufficient speed for the doors to auto lock.

As for your other suggestion, while it has appeal it would be somewhat easier if I were a bloke :P

sounds like a fun relationship :P

seems my memory is abit off although have redeemed my self by finding said post

http://www.skylinesaustralia.com/forums/topic/100905-auto-door-lock/?hl=%2Bmike#entry6656673

Edited by Dan_J
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...