Jump to content
SAU Community

Recommended Posts

Over the weekend I have noticed an unusual sound from the rear passenger side wheel which i suspected might be the bearing. Over the last few days it has got worse.

So I took the wheel off and it turns out that it is the wheel bearing as there is a little bit of play when moving the top and bottom of wheel back and forward.

Just wondering how hard of a job is it to replace the bearing as I understand that it is held in by four bolts and it is not pressed in.

I do not have any fancy tools so if I was to attack the job, would I managed to get it off and replaced?

Thanks for any advice in advance.

Link to comment
https://www.sau.com.au/forums/topic/429549-r34-rear-wheel-bearing/
Share on other sites

Taking the bearing out is easy but then you have to remove the bearing from the spline thats the hard part, youll need to make a few special tools to pull it off. Other problem you run in to is they seprate into 2 pieces when trying to press it off the spline and your left with half still on.

Putting tge new one onto the spline is easy enough if u have a press.

OK thank you for the advice.

This is the one which I have just ordered.

http://www.ebay.com.au/itm/360701961813?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649

I thought that you have to just unscrew the bolts off the back of it! I did not think that you needed to press or unpress anything!

I think I might just get a mechanic to do the job as I don't have any specialist tools!

So looks like this is the wrong bearing. Got it to the garage and they told me that it was missing the top mount for the hand break. After looking around they managed to get one in however once it was all bolted on they realized that the shaft would not fit as it was 3mm to small!

I had no idea that the there different sizes!

Can anyone help me with this as I can not find the correct bearing for my car?

So looks like this is the wrong bearing. Got it to the garage and they told me that it was missing the top mount for the hand break. After looking around they managed to get one in however once it was all bolted on they realized that the shaft would not fit as it was 3mm to small!

I had no idea that the there different sizes!

Can anyone help me with this as I can not find the correct bearing for my car?

Hey mate, hopefully im not too late on this one.

R34 GT and GTT's are different..

GTT's run the GTR rear hubs and GT/V's run the S13-15 R32-R33 non GTR hubs, the one's you bought off eBay will fit any S and R chassis minus the GTR's and a 34GTT's.. the one you would need is in the link below, its what Just Jap supply but you can see the difference.

http://justjap.com/store/product.php?productid=19774&cat=375&page=1

I hope this helps as most listings for rear wheel bearings miss this very vital piece of info.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've got a 2011 J50 that I imported six years ago. The unmodified factory AV system date and time has always been correct ( Japanese timezone of course ) up until last month. About two weeks ago, at engine start, the system wished me a happy new year ( in Japanese of course ). I can't think of anything that would make the system think that the date had changed, unless the GPS component has failed/reset somehow ? I checked the GPS reception in the system settings, and it can still see the satellites. Has any other J50 owner had this happen ?  It's no biggie, just annoying that it tells me the wrong date anytime I start the engine. 😅
    • Love following your adventures on IG, hopefully if you're still around in Japan when we visit again wouldn't mind going for a few beers with you (that's if you're keen on hearing how I hate Nissans).
    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
×
×
  • Create New...