Jump to content
SAU Community

Recommended Posts

Due to work commitments, I am about to start parting out my DR30 project, with alot of parts available, is there much interest from anyone in WA for anything?

I really can't be bothered shipping anything large interstate. Most parts are brand new.

Parts include;

Iron mask front end

Vented FRP Iron mask bonnet

Jenesis FRP front lip and side skirts

Jenesis FRP front bumper (needs repairing)

8 point bolt in cage from Japan.

Complete interior (minus seats) with several brand new parts from Nissan. Uncracked dash.

Recaro seats with mesh head rests and R30 rails.

Jenesis 260 km/h speedo with 10,000 rpm tacho

Front and rear windscreens

Brand new coupe rear lower chrome window trims.

Jenesis oil cap and gear knob

If anyone in WA is interested, the shell (unregistered) is available as well, can do a deal if anyone wants the shell and all the parts. Shell is currently in 2 pac primer.

At this point in time the engine and gearbox is not available.

Cheers,

Steve

Edited by masTers
Link to comment
https://www.sau.com.au/forums/topic/429919-any-r30-coupe-owners-in-wa/
Share on other sites

Willing to ship, bulky items you will have to organize shipping yourself (to the point of having someone pick it up from my place as I am too busy with work to drop it anywhere)

Edited by masTers

Will send the front bar if you are patient with me in getting it shipped.

I am happy to wrap it in bubble wrap or cardboard, if you can organize to have it picked up from me (Dianella 6059 for reference)

IF it needs to be dropped to a depot, It could take some doing, but not impossible. I am in the middle of busy season at work so for large items I am quite time poor.

I am willing to post the rear moulds (assuming this is what you mean?)

DSCF20021.jpg

The following parts are gone;



Iron mask front end


Jenesis FRP lip and skirts


Recaro seats with mesh head rests


Jenesis 260 km/h speedo with 10,000 rpm tacho


Jenesis oil cap and gear knob


Grey tail lights


Shell is gone but the Body Loom and engine harness are still available (no ECU)


Edited by masTers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...