Jump to content
SAU Community

Recommended Posts

Just seeing if anyone here has a HKS T51R KAI BB turbo with 1.00 rear housing for sale in good condition. Must be ball bearing version. I have up for sale my garret cgc t04z with .84 rear housing so once that sells I will be ready to buy or If someone is willing to trade my t04z for there t51r with cash your way I am willing to do that also. Just seeing what's out there. Please pm me with what you have.

Link to comment
https://www.sau.com.au/forums/topic/430343-hks-t51r-kai-bb/
Share on other sites

It's still on my car atm so I can get pics this weekend.

it's a garret cgc t04z with .84 hot side rear housing, is sitting on v band manifold on my car atm.

Easily under 7000ks only ran at 17psi on my car and made 330kw on my supra with stock motor but upgraded fuel system ecu etc.

looking for $1300 atm.

Edited by Mattikin1
Link to comment
https://www.sau.com.au/forums/topic/430343-hks-t51r-kai-bb/#findComment-6973143
Share on other sites

I have seen alot come up in the past for alot less than 4k for just turbo so ill see whats out there first before buying yours then trying to sell of the other bits dont see why you wont seperate if its easy to get more money parting as you say.

Link to comment
https://www.sau.com.au/forums/topic/430343-hks-t51r-kai-bb/#findComment-6973332
Share on other sites

I have a RB26 kit for sale.

T51R KAI BB with HKS manifold and HKS II gate. $3500 will not separate.

You can sell the manifold and gate for an easy 2k.

It's looking like it is going to be harder than I thought to find a ball bearing version can you post some pics of yours I might have to resort to getting this. Just wanna see some pics then if I like ill push to sell my t04z quicker.

Link to comment
https://www.sau.com.au/forums/topic/430343-hks-t51r-kai-bb/#findComment-6975988
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...