Jump to content
SAU Community

Recommended Posts

Pretty sure iv seen this in Kent street Hamilton area

Yeah I visit that area sometimes so id say it was me,

Did you have to take the inner guard lining out to fit your grids btw or roll the guards?

I had the guards rolled when they were fitted and the guy zip tied the lining to the guards, bit fiddley but can be done.

are they direct plug in to loom or do u have to get the plug for the injectors and is there any chance of some better pic of it all and is the fuel reg still attach to fuel rail. i keen on it all just what more info

are they direct plug in to loom or do u have to get the plug for the injectors and is there any chance of some better pic of it all and is the fuel reg still attach to fuel rail. i keen on it all just what more info

I will Remove the parts tomorrow and give you a photo of the exact setup and parts, The plugs are part of the sale as I am looking for the stock rail etc off whoever buys this...

cant believe this hasn't been bought yet... the injectors alone are worth $600 and about the best injector on the market.. :/

Edited by AngryRB

PRICE REDUCTION

Fuel setup $650 or $600 +exchange for a stock rail+injectors

post-70965-0-56838000-1378645567_thumb.jpgpost-70965-0-81001700-1378645589_thumb.jpg

Rear Bumper $100

Tein coilovers HA $600 or $500 + exchange for stock suspension

Rota Grids - $700

2 GTR BOV's $70

GTR Cluster $350 or $300 + a stock cluster

Tomei Poncams- $500 + stock cams

P.S- DO NOT ask me to bring the parts to you, do I look like a courier service?? giving me the shits..

Edited by AngryRB

Can I get more pics of coilovers?

There still on car, they are all green like the last pic, will post more pics soon, all in Perfect working condition

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...