Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Sorry, up the road towards city. Units next to the servo (used to be BP?) and Dominos (possibly still there???)

Right near where that mechanic crashed the customers porsche and died couple of years back.

Ahh i see, its a 7/11 servo now and dominos is still there, that's pretty close to my place.

The Breeze is good down there, we go to the park to do our work outs by the river, great spot for it.

Everyone thought it would never flood again I think!

Well if they didn't use wivenhoe as water storage we wouldn't have had the problem in the first place :/

Well if they didn't use wivenhoe as water storage we wouldn't have had the problem in the first place :/

Well it is designed with both storage (46% of capacity) and flood mitigation in mind (54%) and is only designed to reduce peak height by a meter, it achieved this in 2011. It was peoples expectations that failed rather than the dam! Most of the water came out of the Lockyer anyway which joins the Brisbane River below the dam, it was all just a series or really unfortunate events.

Yeah I guess. Then started the blame game :/

Yeah, the flood commission was a total joke with the finger pointing, some of my measurments got submitted as evidence to that, had to go and sit there for a day, terrible waste of everyone's time!

Yeah, the flood commission was a total joke with the finger pointing, some of my measurments got submitted as evidence to that, had to go and sit there for a day, terrible waste of everyone's time!

Such a fun job :P Do you often get questioned regarding the validity of the data you provide?

Such a fun job :P Do you often get questioned regarding the validity of the data you provide?

Always

Yeah although it's not the best image to have the exec arguing publicly like that :P

Just start a little earlier ;) by the time we get there only the crying is left

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...