Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

So all the trouble of boring out a 20 block to fit a 25 head for what?

Its still a 20 head just with a 26 crank and SR20 rods from what I remember of them. The bores are way different 20 vs 25 they're like 80mm in the 20 and 86 in the 25 lol.

Its still a 20 head just with a 26 crank and SR20 rods from what I remember of them. The bores are way different 20 vs 25 they're like 80mm in the 20 and 86 in the 25 lol.

So a stroked 20 essentially? Still a dirty 20 then Martin.

Yep essentially that. So you still have to deal with the shit head on the 20.

I can understand the point of it if you want to run in a class that requires original engine, makes sense but you could probably go just as well spending the money on a good turbo set up for it etc.

Run the pinny in street class instead?

Yep essentially that. So you still have to deal with the shit head on the 20.

I can understand the point of it if you want to run in a class that requires original engine, makes sense but you could probably go just as well spending the money on a good turbo set up for it etc.

Run the pinny in street class instead?

That's what I thought, few decent bolt-ons and you're good to go.

That would require registering it with a full weld in cage.

why dafaq you wanna do that???

May as well just put a 26 in it

Bit more capacity, not going to cost that much more than rebuilding a 25 bottom end, I can still use all my bolt ons, etc.

26 into a 31 is a multi million dollar excersize, and I'd basically have to start from scratch. Why the f*ck would I want to do that?

Why? a 60 with hydraulic lifters. I still say 25/30.

See above.

25/30 is a possible option but will probably need a bigger turbo.

Put down the crack pipe and just get a 26?

See above.

If thats the case I'd just stick with getting another 25 into it. extra money spent on the 26 crank would be better spent on tyres and entry fees.

The difference between the two is only 70cc anyway i doubt it will make that much difference

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...