Jump to content
SAU Community

Recommended Posts

ok i've finally got all my money of those government bastards and i keep getting told i need the power fc not the safc, but seriously i know alot of high hp cars getting arounf with safc's!!! so at what point is the powerfc the better option? i am running a hybrid t3/4 turbo am thinking prolly forged heads and deff a bigger pump so i can run more than the 10psi i can now but wouldnt wanna go much more than 16-8 psi and would be happy with 300-350rwhp....

so what do yaz reckonz ay?

Link to comment
https://www.sau.com.au/forums/topic/4335-safc-vs-p-fc/
Share on other sites

Neither - go Microtech :P

someones selling one here: http://forums.skylinesdownunder.co.nz/show...&threadid=18058

Reason for this is, if you're trying to push out those figures you'll need to change a few other sensors, and at 350rwp you'll need to either upgrade to a z32 afm, or go for a diff ecu, such as the microtech which runs on it's own internal MAP sensor

Power fc is just a drop in replacement, so runs off of the std factory sensors. Allows big tuning but the sensors are still the same and will need to be upgraded

s-afc is only an AFM interceptor, it adds or subracts a small amount of voltage and tells the factoy ecu this, so that you can tune the mixture a little at each load point

I'm pretty sure that you can't put a MAP sensor or anything else, to by-pass the AFM, since it is requiring an AFM signal, and the two aren't in a proportional relationship (ie - not compatible)

otherwise you could run a haltech or microtech in piggyback with the factory ecu, so that you have the new ecu controlling fuelling and spark and the factory ecu controls the idle and air con etc - if cops look in kick panel it shows std ecu, but factory ecu only controlling the basics

they're all good though, just depends on whichever one you want to have :)

also I think s-afc's are 512 bux from nengun, but can't be bothered looking as 56k dial up is pissing me off ;)

Link to comment
https://www.sau.com.au/forums/topic/4335-safc-vs-p-fc/#findComment-68743
Share on other sites

but when using the s-afc you'll be losing kw's

the power fc can be tuned to a fine enough degree (per 500rpm I think...) and thus your power band will be more defined

the microtech I'm pretty sure is universal, and requires a couple of extra sensors (which don't cost much anyway) and a tune up

personally if I were you and you only wanted an apexi piece, then I'd go the power fc

and yep, injectors will need to be upgraded for sure, as well as a few other bits

but with pleasure (fast car :)) comes pain (expenses ;))

taka kaira's url is www.takakaira.co.jp

actually, hmm, doesn't work, maybe it's .com then

I don't know :P

Link to comment
https://www.sau.com.au/forums/topic/4335-safc-vs-p-fc/#findComment-68903
Share on other sites

while we're all on the subject of S-AFC's....

does anyone know what a decent choice is for an S13 sr20det.? I don't want to use a full ecu replacement like a microtech/haltech etc..

so I'm looking at either a piggy back unichip, a S-AFC or getting my ecu re programmed. what ever I choose, I want it to be tunable for a larger AFM like a z32 unit. any suggestions.?

thanks.

Link to comment
https://www.sau.com.au/forums/topic/4335-safc-vs-p-fc/#findComment-68978
Share on other sites

unichips are crap

nuff said :)

it depends on what you've done to your car osc@r, which should determine what you need

and whether you intend on doing anymore modding after the chip

if you are still doing other stuff, then reprogramming your existing ecu (someone correct me if I'm wrong) but that will only remain set to how it was when you had it reprogrammed. That is, if you do additional things to your car it will require retuning, and will cost another few hundred bux. But for up to 500 dollars for an s-afc (which can be tuned at any time) I'd say that that would be well worth it (if you don't want a whole new ecu)

sory if it doesn't make much sense, getting tired!! ;):D

Link to comment
https://www.sau.com.au/forums/topic/4335-safc-vs-p-fc/#findComment-69047
Share on other sites

  • 4 weeks later...
Originally posted by skyzerr33

dude with those figures your after u need the pfc as you'll likely need new injectors and the safc want be able to use them to there max potential.

and 500-600 for a safc is abit much even for nengun

pay 540 tops from him or go to takakaria

Recently I was selliing them for $475 AUS Delivered.

Link to comment
https://www.sau.com.au/forums/topic/4335-safc-vs-p-fc/#findComment-80150
Share on other sites

because ignition changes are expensive. eg remap = $500 per tuning session

SAFC's cost $100 for a re-tune. if youre continually modding your car then its unrealistic to keep paying out the large amounts for remaps etc when SAFCs (which may not be the final solution) can provide some tuneability. ignition tuning is also limited by our pump fuel compared to japans isnt it?

i plan on getting a remap once ive finished modifying, but for now the SAFC provides enough tuneability to keep the car runing relatively smoothly. shannon: if youre finished modifying, remap. if you plan on doing more than SAFC simply because its cheaper to re-tune once you modify further

Link to comment
https://www.sau.com.au/forums/topic/4335-safc-vs-p-fc/#findComment-80572
Share on other sites

you know once you done the $500 chip.... it can easily be retuned at std tuning cost?

lets see remap $500 plus tune ignition and fuel

Vs

safc $400 plus tune only ever going to do fuel but has extremely sweet rice value blue screen

mmmm

Link to comment
https://www.sau.com.au/forums/topic/4335-safc-vs-p-fc/#findComment-80577
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can ship Nismo floor mats to you: https://www.oemsoko.co.jp/products/nismo-floor-mats-for-skyline-r33-bcnr33-stagea-wgnc34?_pos=1&_sid=9278c1467&_ss=r  
    • Here's the link: https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6642/misc/G49?frame_no=WGNC34-137122 What you think about it? The same product i found on nengun: https://www.nengun.com/oem/parts/40567/MiPwn5qAMfCfmpxHNDnwn5q9MDAx8J-QiW9sZC1qcC0xMTAtRzQ5LS0wMDE/Floor+Carpet+%2F+Mat+2/0688339eba149c19 Bot i have spoken to 😅 ensured me, that mats are 100% original, oem product. I have my doubts. I also heard what you mentioned, that nengun often offers items that are actual not available... On the other hand mats i found on japanese yahoo or ebay are in poor condition and still quite expensive so i'd rather wait for some better offers. My location - Poland. We literaly don't have ANY market for used Stagea parts so need to search outside Europe.
    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
×
×
  • Create New...