Jump to content
SAU Community

Recommended Posts

contact whistla on these forums, he's in VIC too and got his Wolf 3d installed in his R33. I think his was manual tho. Work was done by some rotary workshop from memory.

i have a wolf plug in in my auto r33 the only thing thats wrong with it is gear changing from 1st to 2nd is pretty hard and it holds gears longer i had mine supplied and fitted by peter at rank rotary in mentone ph 95851906

That seems to be the problem with aftermarket ecu's in autos, the gearchange quality suffers. That's why I am going with the less than perfect solution of an SAFC. :)

gear change isnt a problem as long as you bridge across the plug for both the 3/4 throttle position (kickdown) and the TP sensor for shift points. These inputs go into the original ECU, then back out to go to the PCM.

Mine changes beautifully....

gear change isnt a problem as long as you bridge across the plug for both the 3/4 throttle position (kickdown) and the TP sensor for shift points. These inputs go into the original ECU, then back out to go to the PCM.

Mine changes beautifully....

Hi i dont spose you have any pics of the plug that has to be bridged? did you do yours yourself?

its the plug at the ecu, you just have to bridge some pins at the plug.

I have all the diagrams somewhere, ill have a look tomorrow and let you know, what i have here is the signals go from pins 38 and 57, i think they go to pins 14 and 5, but ill have to look at mine to be sure and see which one goes where.

a mate of mine is selling a brand new plug in wolf with warranty etc all brand new in the box never used for 1300 i dunno what thats like price wise but it sounds ok to me..... if u are at all intrested it may save ya some cash... cheers Jon

That's the price you buy it from the "retailer", no savings there.

I too have a wolf 3D, my car is a manual. Also tuned at Rank Rotary, with some finner idle adjustments done at EAS Performance.

i didnt get around to it today, but the easiest way to do it, the way i did, is the check pins 14 and 5 with the nissan ecu connected, see what voltages they have coming out (use a digital multimeter, NOT analogue). one should have a voltage that increases from around 0 volts closed throttle to around 5 volts WOT. This pin is the sensor signal OUT to the PCM. Once you have found it, and you have your new computer ready to plug in, simply run a bridging wire from pin 38 to the one that showed the variable voltage.

Without this feed from the TPS, the PCM has no idea of throttle position, so upchanges and down changes will be erratic, AND, line pressure could also be low, which could cause slippage in the clucth packs and bands.

I think from memory that the 3/4 postion throttle switch also goes out to the PCM, for kickdown, but i'll have to check mine to be sure.

I'm not running the wolf, im running a motec m48, but obviously the principal is the same.

Hope this helps.

This wiring diagram is one of the best i could find, its large, (1.2 mb jpg) but very clear.

If you can, print it out on A3,.

http://members.iinet.net.au/~kbam/rb25diagram.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...