Jump to content
SAU Community

Microtech Lt16 Suit Rb26 With X6, 3 Bar Map Sensor, Ecu Logging

ISL33P
 Share

Recommended Posts

ISL33P Proficient

ISL33P

Posted
Posted (edited)

FS: Microtech LT16 to suit RB26 with brand new harness, 3 bar map sensor & ECU logging. Also comes with X6 ignitor box and new harness. Purchased computer alone 2nd hand and I have receipts for everything for Microtech which confirm the specs and configurations. Was used in car for 2 dyno sessions, which can be confirmed by reputable previous workshop owner/tuner.

This setup brand new is approx $1700, I am chasing $1300 ono including delivery anywhere in Oz.

Thanks,

Ariel

Call/sms 0403279000

post-16214-0-88925800-1385186220_thumb.jpg

Edited by ISL33P
ISL33P Proficient

ISL33P

Posted
  • Author
Posted

Was initially in a tt lsx powered car for 2 dyno sessions. Tuner then became a Haltech distributor hence the computer change, no other reason. Was reconfigured to suit rb26 with invoice receipts to back it up.

No longer for sale - please delete

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Just a standard sanding block size. With the rock chipa they are quite small. I sanded them as you could feel the edges. 
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Say you've just laid all your filler and your about to start sanding, how large is the sanding block your using?  Like a high fill primer? Technically possible but would be a nightmare. Just guessing from the photo, but they look small enough that you might get away with using a 1k spot putty. Normally you'd use something like this on pinholes but with the type of project you're working on I'd give it a go. 
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Omg Brake pedal removal.. FML!!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
×
×
  • Create New...