Jump to content
SAU Community

Recommended Posts

My 1988 Nissan Cefiro has recently failed a WOF on the park, tail and license plate lamps not illuminating with the headlights. Hasn't been working for a few weeks but haven't gotten around to looking into it. Figured it could be the headlight switch on the steering column but testing it seems to show that's not the problem. I've looked at and replaced the blown fuses on the interior fuse block and that's not the problem. I've looked at and tested the tail light relay in the engine bay and thats' not the problem. I have looked into the auto light relay unit in behind the right headlight, and have found slight corrosion on one of the relay power pins, however I don't know if thats the right issue. I'm pretty stumped, and it's probably going to come down to a shorted wire somewhere in the circuit... What do you guys reckon?

Link to comment
https://www.sau.com.au/forums/topic/435800-a31-faulty-headlight-circuits/
Share on other sites

I've had this problem more than once and it was the switch, to test it, unplug the stalk and bridge the two wires together responsible for the running light circuit, I can't remember off the top of my head which wires but I will check tomorrow.

It's probably a smarter idea to bridge them via a fuse and see what happens, but if there is a short circuit and you bridge it with a little piece of wire you'll know about it pretty quickly (it will get HOT), but then again your fuse should have popped if that's the case already.

It could be an incomplete ground anywhere on the circuit, which was my problem the first time (front left parker globe holder), so check your parkers first, it's very unlikely to be a ground in the interior.

The headlight circuit will run fine without that brown box plugged in, so don't worry about that.

I'm using an S13 switch at the moment while I source a working A31 switch, the running lights only come on when the headlights are on (second click), they don't come on with the first click, not sure if that's because if a different design to the A31 stalk or what, but an S13 stalk should get you out of trouble in the meantime.

I've had this problem more than once and it was the switch, to test it, unplug the stalk and bridge the two wires together responsible for the running light circuit, I can't remember off the top of my head which wires but I will check tomorrow.

Sounds like a plan. While I had the stalk out, I used a screwdriver to bridge the center contact with the contacts on either side of it and the system worked fine, so my assumption was the switch worked fine but there was something further along in the circuit that wasn't bridging it properly.

EDIT* Although now that you mention things popping... I had my left hand headlight die around, if not at the same time, as my running lights failing... but my headlight fuses are perfectly fine. Possibly a bad earth around the headlights?

Edited by promaori

my left headlight globe went a few months before I had some drama's as well, so yeah something sketchy in the design in that front left corner I think...although headlights are on a completely different circuit so they should be unaffected

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
×
×
  • Create New...