Jump to content
SAU Community

Recommended Posts

the other day i uped the boost on my r33 so that it know runs around 10-11 psi but dont know if this model has a boost cut or i have some bad fuel, or maybe time for some knew plug. once it gets boost of 10-11 it splutters and pops through the exhaust. the plugs have done 25000 kms and the fuel im using is mobil.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/
Share on other sites

sorry as far as i know they have a boost cut for over boosting, I ran 14psi and no drama's, my car did suffer a broken land on piston 6, just when i bought it, because of a failing fuel pump, I found out after the rebuild that the fuel pressure dropped away under load. this was before I did any mods to it. a new 044 and she was a steady pressure again.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-891084
Share on other sites

Cav its your plugs, I just went through the same prob last weekend, car loosing power like spark or fuel cutting at anything higher than 9psi.

I replaced the plugs from fairly new NGK's to Double Platinum Autolits $90 all up and was advised by two different GTR specialist one online in N.Z skylinesdownunder forum to gap them to .66 So I took them as close as I could to that and guess what, it bloody worked, boost is fine all the way to 12psi - not game to take any further till I get a front mount.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-894992
Share on other sites

i found iridiums to be shite in my S13 ... soon as i upped the boost with an EBC it started missing. took the iridiums out and put in just your normal cheapy plugs that are like 12$ a set and it worked a treat. id say find out what is the cheap copper alternative to your plugs (NGK brand still though) and put some of them in at the same gap of .75-.8. for $12 it cant hurt to see if it is just crappy plugs.

yeah u need to dyno your car with a fuel pressure guage to test the fuel pressure. however, if you are upping your boost, it is a sensible option to upgrade your fuel pump anyway, especially if your planning to run the higher boost all the time and more power in the future. an 044 intank replacement is usually a good bet.

if it still has issues and you want to go for a Malpassi pressure regulator, do that after you've done the fuel pump. the Malpassi wont do much good if you have a stock fuel pump coz the pump will struggle to keep up the increased pressure anyway. i had a misfire in my DR30 skyline, changed plugs and leads, reset ecu, upgraded fuel pump, and still had a misfire at around 1bar. after fitting a Malpassi Rising Rate regulator the misfire is now gone.

try plug changing and see how you go to start with though!

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-902830
Share on other sites

guys i have changed the plugs with a set of ngk cheapies and still the same. got my mates to watch the ass of it and it is blowing raw fuel out the exhaust. do they have trouble with the coils, maybe one doesnt like the increased boost (extra load). it doesnt play up till high in the revs 5000-6000 rpm. i can run 10-11 psi low in the revs with no trouble.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-909192
Share on other sites

  • 3 months later...
sorry dude havent sorted the problem yet, am thinking coils, or an after market computer its got me stuffed need to get it to someone whos playing with them all the time. i might sell it yet, that will fix it.

luckily it seems it was just my plugs...I hope you get yours all worked out though. Good luck!

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-1054385
Share on other sites

guys i have changed the plugs with a set of ngk cheapies and still the same. got my mates to watch the ass of it and it is blowing raw fuel out the exhaust. do they have trouble with the coils, maybe one doesnt like the increased boost (extra load). it doesnt play up till high in the revs 5000-6000 rpm. i can run 10-11 psi low in the revs with no trouble.

Sounds like a fuel problem dumping too much fuel in and choking on it if its coming out the exhaust as a liquid :uhh: - SAFC ll can fix this.

Could be the coil packs, you'll need to tape them up with duct tape. Because the spark can ark out the side which results in the plug not getting the full spark. Do you run the black cover ontop of your coils - Saying Nissan 2498cc etc... ?

Hope that helps.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-1054433
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...