Jump to content
SAU Community

Recommended Posts

Currently parting out my r33 gtr. I have plenty of parts available, I am located in gympie, Queensland 4570. Apexi power fc L jetro, with hand controller $860 Ono. Injectors dynamics 1000cc injectors $400 Ono, tomei poncams type c $350 ono ! Trust gear knob $40, r33 Gtr front head lights $100 Ono. r33 electic Ariel $55, r33 Gtr original front bar $500 pick up Gympie Queensland. Plenty of other parts available lots of aftermarket.

post-131903-13895040455506_thumb.jpg

post-131903-13895040692448_thumb.jpg

Edited by twinturbzgtt
Link to comment
https://www.sau.com.au/forums/topic/437470-gtr33-part-out/
Share on other sites

  • 3 weeks later...

I have brought this to the attention of my bank and for some reason the $150 I deposited into his account was rejected and credited back to my account before they had to do anything. Some strange shit going on with this guy, not replying to any PM's.

Hopefully other members get their $ back and karma catches up with this little turd in the form of a huge kick in the nuts. Scumbag.

In any case, I'm looking for all 4 wheels inner guard liners and clips for a 33 GTR if anybody has some in good condition. Cheers.

Link to comment
https://www.sau.com.au/forums/topic/437470-gtr33-part-out/#findComment-7184204
Share on other sites

If this guys legit then fair enough, but the parts he quoted were cheap and just found out from my local wrecker that there's a lot of stolen GTR parts coming down from qld, cops have actually tracked parts down and confiscated them.

Link to comment
https://www.sau.com.au/forums/topic/437470-gtr33-part-out/#findComment-7184242
Share on other sites

I reported this member to sau a few weeks ago after some dodgy dealings. I guess an admin should step up and sus them out to protect members of sau!

So hard these days with so many cars getting stolen....just wonder if anyone actually got something off this guy! GTR headlights for $100 cheap, hence why I kept asking for pics

Link to comment
https://www.sau.com.au/forums/topic/437470-gtr33-part-out/#findComment-7184304
Share on other sites

I reported this member to sau a few weeks ago after some dodgy dealings. I guess an admin should step up and sus them out to protect members of sau!

Awesome!

A heads up would likely have saved me some money.

Fair price for what I was chasing, money deposited and now he seems to have gone to ground.

Shame as nearly all the trades I have done on SAU have been excellent.

Lets hope "Shane" fronts soon and sends out the items he has sold.

Link to comment
https://www.sau.com.au/forums/topic/437470-gtr33-part-out/#findComment-7184896
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...