Jump to content
SAU Community

Recommended Posts

Hey guys, I recently bought this GTR and I'm not in a rush to sell it, I love it. I'm just putting it up for sale merely as an expression of interest, an exercise out of boredom if you will. If it sells, I'll move on, if not I'm completely happy to keep it :)

The engine was built by Gavin Wood on the Gold Coast, the mods are as follows:

CP Pistons

Eagle Rods

Tomei 270 cams

Springs/Retainers

N1 turbos with HKS actuators

Full custom tucked 3.5" exhaust and high flow cat made by Fabulous Fabrications (beautiful work) along with custom Hot/Cold cooler pipe.

Intercooler

Haltec Platinum Pro ECU

Bilstein/Eibach strut/spring combo

Cusco Swaybars

Cusco 1.5w rear diff, fully rebuilt and new diff bushing installed with newer (and slightly larger/stronger) R33 half shafts

Ikeya Formula front and rear upper control arms.

HICAS delete.

Desmond Regamasters in 17x10 + 20 wrapped in near new Federal 595 RSR's

The car made 385hp at all four on 18 psi and at a very rich tune of 11:1 up top. If I keep it, it'll be getting a retune shortly for more boost and a little less fuel, but it's quick as it is.

Aircon is cold, chassis rails are straight, no rust, this is a clean GTR :)

2 minor issues, the passenger side dash vent is missing (previous owner broke it trying to install a cup holder) and it needs new coil pack connectors and possibly coil packs. The coil issue will be taken care of prior to sale and I can chuck a vent in it, I just haven't found one for sale yet.

JerryGTR7_zpsb93a24ba.jpg

JerryGTR4_zps97c23603.jpg

JerryGTR10_zps6a90627f.jpg

JerryGTR2_zpsbc3c9bad.jpg

$21,000 ono

Will entertain the thought of trades, just depends on what I'm being offered but send your offers through anyway, it can't hurt!

0401029817

Link to comment
https://www.sau.com.au/forums/topic/437696-r32-gtr-forged-motor-mods/
Share on other sites

Since listing for sale the car has had
New coils (old coils were fine, misfire was being caused by a boost leak thanks for a faulty coupler)
Service in the last 100km
Brake rotors machined and pads linished, brand new pads
Replaced coupler to get rid of boost leak
The car is ready for its new home

It's an 89 Grant, yes I have a dyno graph floating around somewhere.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...