Jump to content
SAU Community

Brakes Squealing....

kawasakirider
 Share

Recommended Posts

kawasakirider Grand Master

kawasakirider

Posted
Posted

Hey everyone, I've got an R32 GTR and I can't get the front brakes to stop squealing....

I do my own work on my own cars all the time, I've done my own brakes time and time again and I've never had a drama. I did my brakes recently on this GTR and the old owner had lost the anti rattle shims, I was in a bind so I fitted the pads without them.

They squealed and I put it down to the absence of the shims, so I sourced another set along with some anti squeal silicone stuff (goes on the back of the pads) and tonight I pulled the brakes apart, roughed the pads up, used the anti squeal paste along with the shims and put it all back together.

I went for a drive and followed usual bed in procedure, I was stoked because the noise had gone. About 10 minutes into the drive it had come back with a vengeance.

What is up with this? Could it be the type of pads (bendix ultra whatever the fark), or could my rotors have an issue?

Almost ready to burn it.

Link to comment
https://www.sau.com.au/forums/topic/438113-brakes-squealing/
Share on other sites
Daleo Grand Master

Daleo

Posted
Posted

Piss those pads off; they're nothing special.

Do yourself a favour & grab a set of Remsa pads from GSL Rallysport. Bed them in EXACTLY as GSL recommend.

Great value rated to 650 degrees. No farkin squealing.

http://gslrallysport.com/remsa

  • Like 1
kawasakirider Grand Master

kawasakirider

Posted
  • Author
Posted

You positive that it's the pad mate?

I know they're nothing special, my pads were just down to nothing and I needed something ASAP, so I grabbed what was available. I've used them before on cars with the same callipers as a GTR and had no dramas with squeal.

Truth be told, the rotors could do with a light machine, but I've had worse rotors in the past that were quiet as.

Daleo Grand Master

Daleo

Posted
Posted

You positive that it's the pad mate?

I know they're nothing special, my pads were just down to nothing and I needed something ASAP, so I grabbed what was available. I've used them before on cars with the same callipers as a GTR and had no dramas with squeal.

Truth be told, the rotors could do with a light machine, but I've had worse rotors in the past that were quiet as.

The squeal could be related to the shims; I've always run them in my Sumitomo calipers, and never had issues.

It could also be incompatibility between the old pad material (layer on the rotors) & the new pads; this is very common.

Some pads will refuse to work with the layer of material left on the rotor from the previous pads; it's always a good policy to give a light skim when changing from one pad material to another, unless you KNOW they are compatible.

Overheating pads in the "Bed In" phase can cause the bonding material to be drawn to the surface; this effectively glazes the pad.

Sometimes scuffing can save them, sometimes they are unsalvageable.

People are tempted to get new pads very hot, by doing heaps of very high speed stops, because they are going to use them hard.

Often, the temps required to set the bonding material are quite low.

The Remsa's have a reputation for not being squealy, nor are they very hard on rotors, but they are dusty. I'll take dust over squeal any day.

Hopefully it's a simple fix.

GTRPSI Mentor

GTRPSI

Posted
Posted

Do the pads have a 45 degree chamfer on the leading and trailing edges? This helps a lot to control squeal.

Normally its the friction of the pads rubbing against the pistons or against the caliper, some old school mechanics use to use copper grease to lube those points.

The outside anti rattle shims can also become weak with use and heat, sometimes a bit of a bend to tighten up the pressure against the pads helps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      I forgot about my shiny new plates!
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
×
×
  • Create New...