Jump to content
SAU Community

Recommended Posts

i have a r34 gtt auto with 117k with the following list of mods

spiltfire coil packs ( have only done about 15000K)

trust turbo back exhaust

greddy ebc set to 11 psi

k & N panel filter

(stock turbo)

so basicly not many mods as you can see.

The problem is that when I start the cold start the car it will shut of straight away, I wait about 10 seconds start it again it goes up to aout 1000 rpm then down to about 400 rpm then up to 600 rpm then bounces between the 2 for a little while. I can drive the car but it seems down on power. It wanst to stall when I come to a stop at a coner but still keeps running.

I have replaced the spark plugs, O2 sensor, Air temp sensor, Fuel fiter & air flow meter.

I have also cleaned the throttle body & aac.

I am using ecu teck to check for error codes and I am not getting any error codes just the 55 code ( all clear)

need any ideas please

Edited by newboost
Link to comment
https://www.sau.com.au/forums/topic/438336-need-help/
Share on other sites

Just a suggestion as I've had almost identical issue in the past.

Check your engine temp sensor connection, (the 2 pin square plug not the Single wire plug)

If it's not connected properly it won't give cold start enrichment, it also won't throw a code.

Mine had a broken clip and was on but wasn't making contact.

Link to comment
https://www.sau.com.au/forums/topic/438336-need-help/#findComment-7184772
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Details: Turbo Borg Warner EFR 9180 with 1.05 rear housing Upgraded TurboSmart integrated BOV Sanded and powdercoated compressor cover in gloss black Elbow welded with wiggins clamp Speed Sensor(Not included) (Can include oil drain(heat wrapped + titanium intake pipe with almost new filter for a tad extra). Manifold: 6 Boost RB26/30 twin scroll manifold  e-MAP ports drilled into both scrolls(I was using the TAARKS EMAP KIT) Turbo is in excellent condition. Always used Penrite 15w50 Racing oil(Changed less then 2000ks). Also using the Turbosmart OP regulator and filter. Downpipe: 4inch Stainless steel with VBand inlet and outlet clamps(included) Heat wrapped Dual ports for Dyno/Wideband usage Will throw in free 2.5 inch intercooler pipe(2.5inch From turbo outlet to 3.5 inch intercooler) - Powder coated black. Turbo made 563rwkw on mainline hub dyno at around 24-25psi boost - Pump fuel. Will def make over 600kw on e85. Didn't bother as my e-MAP was through the roof with my setup sitting past the choke line. I have a cnc ported and fully built head on my 3.2. Turbine speed saw max of around 109k rpm. I'm running this on my R32 GTR, with AC, and the original power steering pump. The manifold clears the AC lines, ABS, and everything else. Although I had new AC lines because I just wanted new ones and I heat wrapped them as well. This will make more power on a slightly lower capacity motor with a higher PR. And I have since upgraded to a G45-1500. Have pics and videos if need be.  Absolutely nothing wrong with setup. Turbo is in perfect condition. No shaft play or oil leaks at all. All the work was professionally done. The transient response of this is fkn amazing. I cannot rave more about this turbo. If I wasn't chasing 4 figures, I would have kept it. $5000 NZ. Located: Auckland, New Zealand.    
    • I particularly like the look of the John Player Special team. (Thumbnail isn't different but hit play for the clip)  
    • Such a cool collection of cars back then.  
    • Mystery solved, thanks bro Bit of a strange mix, but i dont mind it, still looks good. 
    • nah no problems with bearings or hubs.  just the water pump leak and my AC death
×
×
  • Create New...