Jump to content
SAU Community

Recommended Posts

Hey guys,

I think i might have glazed my rotors (pictures attached - ignore the rust as I just finish washing it) so will try to clean that up this weekend

The surface is not rough and brakes doesnt squeel (it did when i was bedding in) so not sure if i'm just over-thinking things

post-38031-0-35988100-1391091043_thumb.jpg post-38031-0-26850300-1391091068_thumb.jpg

Just wondering what's the best method to do it?

Just googling around and ppl suggesting sanding it down using 1200grit then with 2500 grit, and sanding the pads to remove the mirror finish as well then rebed the pads?

Thanks!

Edited by ichi-go
Link to comment
https://www.sau.com.au/forums/topic/438465-glazed-rotors/
Share on other sites

They shouldn't be rough. They should be nice and smooth. If they rust that convincingly after a wash, they probably don't have much in the way of pad binder glazed onto them. I wouldn't worry about it unless you are having problems with the brakes. Brakes shouldn't squeal. If they don't shudder and they bite hard, then they are probably fine.

If you want to clean up glazing, the best way is to go out and re-bed the pads. You need to work your way up to high speeds and hard braking, followed by working your way back down after keeping them quite hot for a while.

Link to comment
https://www.sau.com.au/forums/topic/438465-glazed-rotors/#findComment-7185143
Share on other sites

Hmm you do have a point about the rust, didnt have any problem with the brakes, no shudder and bite hard

I was on the track the other day and i did feel the brake had like an unsmooth surface when you apply the brake (not sure how to describe that feeling) but it was ok the whole day, it was only towards the end of the day that it happened... and my rotors do have this look when it didnt have rust on it:

imag0114mk.jpg

So i assumed i had glazed the rotors

Link to comment
https://www.sau.com.au/forums/topic/438465-glazed-rotors/#findComment-7185469
Share on other sites

I would try to deglaze with a rebed procedure before going to the effort of taking it apart enough to put paper on the rotors. If you sand the rotors you really have to grind the pads back a bit on concrete too, which can lead to them not being even enough etc, and then further glazing problems.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/438465-glazed-rotors/#findComment-7186465
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...