Jump to content
SAU Community

Recommended Posts

Trying to gauge some interest in my motor, not sure what its worth so im trying to sell it for less than half of what ive put into it.

Engine is Non turbo, Has RB30block with JUN oil pump and crank collar, just installed, havent done more than 200kms on it. RB25de Pistons with stock rods, Fully balanced bottom end. The head is a RB25 turbo VCT head with reground cams and oversize valves and some minor headwork done before i bought it. the engine has been rebuild and is no more than 1000-2000 km old. Has a twin throttle body intake with progressive style throttles. this has cost me over $10k

Haltech PS 1000 will be included as will be all wiring, so essentially you bolt in and go.

Will come with the custom made extractors and race pipe, these extractors were made to suit the motor, completley custom cost around $4000 if i recall correctly. they were made in the VL commodore so they will clear the skyline as the VL is more tighter. will come with the 3" side pipe which was another $500

Ill throw in the gearbox, just a standard MX5 manual with an excedy heavy duty clutch put in with new engine, so again 1000-2000kms done on it too.

There may be more ive forgotten to add. if any questions feel free to PM me.

Price $8000 neg. Car makes around 210kw at the engine so the same as a new commodore to compare and around 350nm. Located in sydney.

  • 4 weeks later...
  • 1 month later...

You mentioned you are trying to sell for less than half of what you put into it.

I'm really curious why you would sink so much money into the engine, when it really makes hardly any power?

I understand that some people want to be different, but was there any other goal? Eg particular race class that the engine would fit into?

My mate had his SV6 dynoed at the same place, he has a exhaust and CAI - and just over 30% loss was calculated. and im pretty sure i remember them saying is a 30% loss roughly depending on car. its a HUB dyno. I was hoping it would be a good allrounder on the track but you really need to rev its tits off to get it to go.... in a street car it would be mad fun, take it to the drags it pulls 14 seconds flat. i havent done better....just not trackable how it is. if it doesnt sell soon ill probably turbo it. ill see what happens first

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...