Jump to content
SAU Community

[Vic] Nissan Cube, Series 2, Black, 1.5L Cvt, 45,000Km, 4B Grade, 7 Seater


Recommended Posts

Hello all,


I have just imported a Nissan Cube. My priorities have changed and need money for house now. It is just having compliance finished off this week I have been told by the workshop. Car will be sold with registration. This is the first 1.5l to be complianced in Vic and is one of only a few 1.5l cubes in Vic (none on carsales atm). The 1.5l is said to be more efficient with fuel, has more power and sits at a much lower rev while cruising on the highway. Would make a really fun daily while the GTR sits in the garage for the weekend.


The car looks like new and I had to raise my bid at auction significantly to get a quality car. The series 2 gets a bunch of updates including white dials, different grill, headlights, rear tails, etc.


2006 Nissan Cube cubic 7 seater

Series 2, 1.5l cvt

Black

4B Auction Grade - paid top dollar, auction sheet for proof

45,000km with dereg certificate and service history for proof

Excellent condition in and out (looks new on inside)

Smart key - dont need to use key to start

Full electrics

Dark interior

Auto headlights

Leather steering wheel

Foglights


$13,500 Neg


Phone pics, will upload better later,

1604874_10152532577567571_192927570_n.jp


1521814_10152532577837571_1418251489_n.j


1520663_10152532577952571_2138071548_n.j


DSC09727Large_zpsd901ade5.jpg

Hubcaps are in the car. But would look pretty nice with some mesh rims instead :twisted:

Edited by BigWillieStyles
Link to comment
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Latest Posts

    • I do not think that the return pipe could be the cause of your particular troubles, unless perchance it is leaking in a lot of unfiltered and unmetered air (assuming your ECU is still using AFMs). And then it could be very bad, but it shouldn't prevent you making boost. Blow then engine up from running lean? Sure. But it would make boost. You really needed to disconnect this thing from the turbo inlets and close those inlet ports off a year ago, and you should do it now.
    • Pressure Ratio = 2. ie, 1 bar of boost (assuming 1 bat absolute pressure at the compressor inlet). This is relevant because compressor maps do not have "boost" up the y-axis. They have pressure ratio.
    • Revisiting this thread again x2... 1 year later. This car has been an ongoing project between life. But, I never removed the re-circ pipe. I know, shame on me. But since then, i took it to get tuned and only making about 280hp (lame) and i'm chasing a boost issue where the car wont boost past 7-8psi. Mac valve installed. Haltech Platinum pro with the map sensor.  This is the first time i've tackled the turbo side of things, but i have that side somewhat taken apart to chase the waste gate vacuum lines. And noticed this stupid pipe again. I'm peicing together the puzzle and @GTSBoy mentioned that it was a big vaccuum chamber and said a bunch of car math stuff that I couldn't quite follow the car math (im trying). You guys think this would be the culprit? between rotting vacuum hoses?  i'm making a DIY boost leak tester this weekend. 
    • I just spent a silly amount of time reading other forums' posts and watching "whats this noise" videos on Youtube. It *appears* to be the front diff having killed a pinion bearing or similar. Its almost definitely driveline, I haven't tested to see if the car makes the noise in N though but either way I think it's gonna be pricey. This is outside my area of comfort and expertise so I'll get my BMW guys on it. The bearings are attached to the hubs so are super easy to replace (at least in comparison to press in bearings) so I'll do them also. 
×
×
  • Create New...