Jump to content
SAU Community

Recommended Posts

FS - Haltech PS2000 with uncut / unused short loom + sensors

Selling a pretty much unused haltech ps2000 with short autospec flying loom.

The ECU was powered up via a smart wire and I began to load stuff in for a 2j.

No longer needed, looking for $2200 negotiable.

I have the mounting kit for it, I don't like them, I have no need for it so I will also include that.

I also have an AEM 3.5 bar map sensor that I will include for an extra $50

I also have a couple of coolant and air temp sensors that I'll never use again, one requires connector with plugs, $20 each.

Probably some other crap that goes with it that I wont ever be using like techflex braid.

Located on the Gold Coast, pick up is welcome, otherwise buyer pays postage.

  • 2 weeks later...
  • 2 weeks later...

Hey,

I'm considering one of these with a long loom but your price is quite high for a second hand unit :-(.

Your short loom version is listed on haltech site for $2,354.95 delivered.

OK. I am saving you $155 for a unit that's only been powered up, flashed to the latest firmware and had a supra load file configured to the ecu. Its hardly even been used. Its never ran an engine and its still with the original box, USB cable and software CD.

No one stopping you from buying the same thing direct from haltech for more money or you can save a little and buy mine.

I dont know what gives you entitlement to comment that my second hand ecu is priced quite high but I honestly don't care.

If you want to post links up to the same package as I have that's sold or advertised for less than what I'm asking for then please feel free to do so.

If my price is an issue for you then look elsewhere. I'm in no rush to sell it and could easily still keep it for a future project.

Thanks

  • 2 weeks later...

Did you even read the first post I made?

$2200 negotiable, with the mounting kit and a number of sensors at a reduced price?

If you're interested then why don't you put your money where your mouth is and make me an offer?

Worst I can say is no.

I have an engine lined up that I can use it for but if someone wants to give me a good offer then I'll sell it and wait for their Elite ecu to be released.

Either way, I don't really care as this will run the engine just fine.

Thankfully neither one of us really care :-)

Not suited to my needs as chasing one with long flying loom which comes with new, however alone is $500+

unavoidably will be buying one new closer to build completion.

GL.

Haha

You're a Muppet.

Firstly you cannot even read then you whinge and moan that its not cheap enough now you're saying its not suited to your needs.

Have fun paying full retail.

f**king idiot

  • Like 2

Bla bla bla said the foul mouthed bogan!

Oh hang on there's a heap of people lining up to buy your overpriced sh!t.

Full retail? Ha!

Right back at ya douchebag :-)

Edited by pauls

You want to sort this out in person?

Overpriced shit? I don't get why you cannot get it through your head that it says negotiable. Its been negotiable since the day it was advertised.

Dumb people like yourself annoy me. You cannot read. You continue to comment on the price after being told several times that its negotiable. What is so hard to understand about that?

Calling it shit too? You've admitted that you'll have to buy one yourself!

You need to put your lack of money back into an education because you really are one dumb f**king idiot.

I'm glad you continue to post, everyone can see how much if a complete retard you are! Please keep posting too.

Edited by [200]
  • 1 month later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...