Jump to content
SAU Community

Fs - Haltech Ps2000 With Uncut / Unused Short Loom + Sensors

[200]
 Share

Recommended Posts

[200] Mentor

[200]

Posted
Posted

FS - Haltech PS2000 with uncut / unused short loom + sensors

Selling a pretty much unused haltech ps2000 with short autospec flying loom.

The ECU was powered up via a smart wire and I began to load stuff in for a 2j.

No longer needed, looking for $2200 negotiable.

I have the mounting kit for it, I don't like them, I have no need for it so I will also include that.

I also have an AEM 3.5 bar map sensor that I will include for an extra $50

I also have a couple of coolant and air temp sensors that I'll never use again, one requires connector with plugs, $20 each.

Probably some other crap that goes with it that I wont ever be using like techflex braid.

Located on the Gold Coast, pick up is welcome, otherwise buyer pays postage.

  • 2 weeks later...
  • 2 weeks later...
pauls Rising Star

pauls

Posted
Posted

Hey,

I'm considering one of these with a long loom but your price is quite high for a second hand unit :-(.

Your short loom version is listed on haltech site for $2,354.95 delivered.

[200] Mentor

[200]

Posted
  • Author
Posted

OK. I am saving you $155 for a unit that's only been powered up, flashed to the latest firmware and had a supra load file configured to the ecu. Its hardly even been used. Its never ran an engine and its still with the original box, USB cable and software CD.

No one stopping you from buying the same thing direct from haltech for more money or you can save a little and buy mine.

I dont know what gives you entitlement to comment that my second hand ecu is priced quite high but I honestly don't care.

If you want to post links up to the same package as I have that's sold or advertised for less than what I'm asking for then please feel free to do so.

If my price is an issue for you then look elsewhere. I'm in no rush to sell it and could easily still keep it for a future project.

Thanks

  • 2 weeks later...
[200] Mentor

[200]

Posted
  • Author
Posted

Did you even read the first post I made?

$2200 negotiable, with the mounting kit and a number of sensors at a reduced price?

If you're interested then why don't you put your money where your mouth is and make me an offer?

Worst I can say is no.

I have an engine lined up that I can use it for but if someone wants to give me a good offer then I'll sell it and wait for their Elite ecu to be released.

Either way, I don't really care as this will run the engine just fine.

pauls Rising Star

pauls

Posted
Posted

Thankfully neither one of us really care :-)

Not suited to my needs as chasing one with long flying loom which comes with new, however alone is $500+

unavoidably will be buying one new closer to build completion.

GL.

[200] Mentor

[200]

Posted
  • Author
Posted

Haha

You're a Muppet.

Firstly you cannot even read then you whinge and moan that its not cheap enough now you're saying its not suited to your needs.

Have fun paying full retail.

f**king idiot

  • Like 2
pauls Rising Star

pauls

Posted
Posted (edited)

Bla bla bla said the foul mouthed bogan!

Oh hang on there's a heap of people lining up to buy your overpriced sh!t.

Full retail? Ha!

Right back at ya douchebag :-)

Edited by pauls
[200] Mentor

[200]

Posted
  • Author
Posted (edited)

You want to sort this out in person?

Overpriced shit? I don't get why you cannot get it through your head that it says negotiable. Its been negotiable since the day it was advertised.

Dumb people like yourself annoy me. You cannot read. You continue to comment on the price after being told several times that its negotiable. What is so hard to understand about that?

Calling it shit too? You've admitted that you'll have to buy one yourself!

You need to put your lack of money back into an education because you really are one dumb f**king idiot.

I'm glad you continue to post, everyone can see how much if a complete retard you are! Please keep posting too.

Edited by [200]
  • 1 month later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...