Jump to content
SAU Community

Recommended Posts

Left over parts from wrecking my Black R33 GTST S1.5.


All large parts are pickup in Macleod, VIC, but some smaller ones can be posted at buyers cost.


All parts are in pretty good condition unless stated and prices should be pretty good unless it's a bit of effort to get the part out.


Check out the list and let me know if you further info or pics.



HKS Pod filter with adaptor - Needs new foam $30

Intake manifold - No sensors $50

Engine mounts $50

Radiator overflow bottle $20

Aircon condenser with piping $50

Power steering pump $75

Power steering reservoir $20

Alternator $65

Fuel pump - No label but was fine for 285+rwkw $60

Clutch master cylinder $50

Manual pedal set $60

Tail shafts $60


Exhaust

Decat pipe - Straight 3in bolt on $30


Wheels

Impul NS-01 light weight racing 17in inc Federal tyres, 70% frt, 40% rr $600

Front 5 stud hubs $60

Spare space saver wheel $40


Stock Suspension

Front castor rods $75

Front upper control arms $50

Rear control arms $75


Brakes

Discs Front $40

Master brake cylinder $50


Exterior

Body shell Still complianced and registerable $400

Rear reinforcement bar $80

Bonnet latch $30

Side skirts Stock or type M $100

Spoiler - Series 1 No stop light and scratched $30

Bonnet Black - resprayed $120

Boot Black $50

Front wheel liner Front RH $15

Series 1 tail lights pair $60

Indicators Nismo Side - clear pair $35


Interior

Front Recaro $160

Wiring loom $120

Rear seats $40

Seatbelt set minus front buckles $60

Instrument panel $60

IP cross car beam $50

Centre console $20

Headliner $30

Handbrake front section $40

Taco - 4in with shift light $60

Pillar trims $20

Link to comment
https://www.sau.com.au/forums/topic/440678-vic-r33-gtst-s15-wrecking-leftovers/
Share on other sites

Steering wheel?

Still on the car but the edging is not in great condition why I hadn't listed it yet.

If still interested I can at least put up a pic tomorrow.

Parcel tray ?

You'll hear it before you see it

Sorry mate, already sold.

The list above is pretty much everything that's left other than a large bucket of bolts that would hold the whole car together.

hey man, how much for the indicators + postage to melbourne (3040)

thanks:)

$30 pickup in Macleod or $40 delivered to 3040. Still in excellent condition!!

Rear wiper arm with plastic bolt cover?

I thought it was gone but I actually still have it with the bolt cover. Pic attached.

$25 pickup or $35 delivered.

post-7819-0-52487200-1395739799_thumb.jpg

Edited by Steg33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...