Jump to content
SAU Community

Recommended Posts

hey guys i have a great pair of genuine s3 gtr headlights on my gtst, im selling because im running low on cash.

i also have a s1 bonnet in white that i am selling as i want to take my car back to a s2 front end...

basically ive been to alot of wreckers and they have all been amazed i have these and how good the quality is,

for the headlights i want $1500 they are perfect have no scratches or broken clips/mounts.. hids work perfect.

for the bonnet i want $300ono the bonnet has no bog and is ready to go.

if u have a r33 gtst s2 headlight set in perfect condition and if u also have a white s2 bonnet is good condition

i will straight swap plus $1000 cash my way as my car is drivable now and dont really want to sell seperate so

i can re-install and keep on driving...

if u do have the $1500 i will sell the headlights and hunt every other part down myself i dont mind too much,

i am open to possible offers such as a turbo kit or piggyback/ecu ready to go to get me some big power as

my new car is almost standard parts i already have include...

greddy profec b-spec2

turbo back 3" exhaust

fmic

pod

turbosmart bov

so if u have something compatible with my mods to get me some good power we might be able to come up with a deal..

im at home all day so if u really are interested i can send through pics "headlights are great no yellowing"

NO TIME WASTERS only real buyers that know the headlights are worth it. i live in sydneys west nsw and u can contact me on

0424 842 043 call or text.

"I dont normally come back on here and check for PMs so pls try and get to me through my mobile number Thanks!

i thought ide add one quick photo for proof so here you go ide also sell the s2 front bar with lower bar addon if the headlights

sell as ill be going back to a trust front bar, needs to be reprayed but its all genuine

post-28365-0-85059000-1397954107_thumb.jpg

Edited by Stealthynsa

that would be alright but rego runs out on the 22nd so couldnt get the car there :( it will be registered again a couple of weeks from now so ill have to deal with internet sales, but might take the misses car and come check it out sounds good, is there an entry fee?

my post is also advertised on skyline parts on facebook and also gumtree is there anywhere else anyone could think off to help with my sale cause im hoping after selling the lot ill still have enough maybe $200 short of getting all my front end done and paying for 6months rego

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...