Jump to content
SAU Community

Recommended Posts

Up for grabs is a fully manualised RE401a auto box with 3200rpm stall converter

box was supplied by MV autos with receipt to go with.

The box was in my 25/30 combo but unfortunately the fella just plugged it in without the manual shift control so it lasted not even 2000km's before 3rd & 4th clutch let go, 1st and second still fine, wired in properly they are an easy 350kw setup.

Spoken to trans shop and has estimated repair at min $300 the original purchase was over well over $2500 will supply contact if wanted.

Will not be on offer long or I will have the work done and keep.

$600 FIRM pickup Penrith nsw

Dude, I really recommend getting it fixed then selling it. Your only up for 300 so you say, then you can sell it for 3 times what you are asking easily I would be interested when it's fixed. Not now though

Quick chance for someone to snap up a good setup for a fraction of what I have paid, with minimal outlay. I originally took the car to a less desired trans shop in Penrith (bad move) who quoted min $1200 and told me they had never actually had 1 in before. So I went off their advice and bought another setup. Was later recommended to someone that actually knew what they were doing, and did the wiring and fitment of my new one.

If I get someone genuinely interested I will supply the shop number that fitted my new one and they can call and confirm.

The manual valve bodies are $550 alone + $500 for the stally.

If I get it fixed it will go in my brothers turbo GQ.

Edited by Caelen

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...